background image

6

C

HAPTER

 : Q

UICK

 I

NSTALLATION

 G

UIDE

 

FOR

 

THE

 S

UPER

S

TACK

 II S

WITCH

 1100/3300 ATM E

XPANSION

 M

ODULE

Figure 8   

Velan Configuration Submenu

Configure Submenu

The Configure submenu appears in Figure 9.

Figure 9   

Configure Submenu

Setting up an ATM VLAN/ELAN

1

Go to the Configure submenu. 

2

Select [2] add.

3

Enter ELAN name as configured in the LECS, and the 
802.1Q tag as configured in the 1100/3300 VLAN 
settings.

4

Observe creation and enabling of a new VLAN/ELAN.

Manufacturing default gives this product a single 
VLAN/ELAN, i.e. the Admin VLAN/ELAN which cannot 
be changed or deleted. The ELAN name is “admin”, 
the VLAN/ELAN ID is 1, and the 802.1Q tag is 1.

Copyright © 1999, 3Com Corporation. All rights reserved.
Unless otherwise indicated, 3Com registered trademarks are registered in the 
United States and may or may not be registered in other countries.

3Com, CoreBuilder, SuperStack are registered trademarks of 3Com 
Corporation. Other brand and product names may be registered trademarks 
or trademarks of their respective holders.

Written and edited by Laura Novich and Marvin Rabinovitch. Formatted by 
Debbie Zioni. 

Part No. DIA3311-0AAA04

Published June 1999

velan 
[1]configure

- Configure VLAN/ELAN parameters ->

[2]elanState

- Start/Stop/Restart ELAN

[3]display

- Display summary VLAN/ELAN information

velan/configure
[1] display 

 

 - Display VLAN/ELAN information

[2] add 

 

 

 - Add VLAN/ELAN

[3] delete 

 

- Delete VLAN/ELAN

[4] statistics   - Display VLAN/ELAN statistics

Summary of Contents for SuperStack II Switch 1100







Reviews: