manualshive.com logo in svg

3Com Router 3000 Series, Manual, Page: 9 / 37

Share
Download
3Com Router 3000 Series Manual Download Page 9

1.1.10. VPN 

Symptom Solution 

The basic version of this release does not 
support GRE or L2TP. 

Use the extended version of this release for 
GRE and L2TP tunneling support. 

A Windows 2000 or Windows XP client cannot 
connect to a 3Com router using L2TP over 
IPSec. 

L2TP over IPSec support on Windows 2000 or 
Windows XP clients requires modification of 
the Windows Registry and a static IP address. 
Refer to 3Com Knowledgebase solution 
3KB9023 for more details. 

1.1.11. QoS 

Symptom Solution 

NBX Layer 2 traffic cannot be classified for 
QoS. 

Use Layer 3 prioritization. 

QoS is not supported with the Encryption card 

In order to use QoS with IPSec, use a software 
encryption policy instead of a hardware 
encryption card policy. 

After configuring QoS Policies on a Virtual 
interface, QoS does not take effect 

The virtual interface must be shut down by 
shutting down all of the physical interfaces 
before the new QoS policy will take effect 

The 

undo wred weighting-constant

 

command will not execute 

To restore the weighting constant to its default, 
use the 

wred weighting-constant 9

 

command. 

The undo 

wred ip-precedence

 

value

 

command will not execute 

To restore the wred ip-precedence parameters 
to the default, use the following command: 

wred ip-precedence

 

value

 low-limit 10 high-

limit 30 discard-probability 10 

1.1.12. Dial-Up 

Symptom Solution 

The router reboots after a HyperTerminal 
session is disconnected from the  
1-Port Synchronous/Asynchronous SIC, 4-Port 
Synchronous/Asynchronous MIM, or 4-Port 
Synchronous/Asynchronous MIM with X.21 
support. 
HyperTerminal is not supported on these 
modules. 

Remote console administration can be 
achieved by dialing into a modem connected to 
the AUX port configured in flow mode.  
 

1.1.13. Documentation 

Symptom Solution 

There is no support for NTP Broadcast Delay, 
or NTP Synchronization Period in the CLI, yet 
they remain in the user documents. 

Disregard documentation on these features 
within the user documents. 

The 

setup

 command is documented but 

missing. 

 

Use CLI commands for your initial 
configuration.

 

The 

synchronization

 command is listed in the 

documentation but cannot be used.

 

This command is no longer supported. BGP 
synchronization is always disabled. 

3Com Router Release Notes for V1.20

9

Summary of Contents for Router 3000 Series






































Reviews:

No comments