manualshive.com logo in svg

3Com CoreBuilder 9000, Command Reference Manual

The 3Com CoreBuilder 9000 is a state-of-the-art networking device offering high-performance and robust capabilities. Enhance your network management skills with our comprehensive user manual, available for free download from manualshive.com. Empower yourself with in-depth knowledge and optimize the potential of this exceptional product.

Share
Download
background image

ip multicast dvmrp tunnels define

511

ip multicast dvmrp

✓

 3500

✓

 9000

9400

3900
9300

tunnels define

For CoreBuilder 9000: Applies to Layer 3 switching modules only.

Defines one end point of a DVMRP tunnel. The other tunnel end point lies 
on an IP multicast routing interface on a different system and 
subnetwork. One or more unicast routers lie between these tunnel end 
points. 

Valid Minimum Abbreviation

ip m d t d

Important Considerations 

■

IP multicast tunnels are not required in all networks. Configure a 
tunnel only if you need to have IP multicast traffic forwarded through 
one or more routers that do not understand IP multicast protocols and 
would therefore filter IP multicast packets. Because IP multicast 
packets are encapsulated in unicast format at the tunnel entrance 
point, the interim routers in the tunnel forward the packets onward 
toward the other tunnel exit point.

■

Think of an IP multicast tunnel end point as being layered on top of a 
regular DVMRP routing interface. Therefore, before you can define a 
multicast tunnel end point in your system, you must first define at 
least one IP virtual LAN (VLAN), define at least one IP interface, and 
enable DVMRP on the interface. 

■

The remote tunnel end point must lie on a different system and 
subnetwork. 

■

You must define the tunnel on both end points — that is, on both the 
local system and the remote system — even though you specify the 
address of the remote interface in the local system. 

■

When you define a tunnel with local and remote addresses, the 
system automatically assigns the value 1 as both the tunnel metric and 
the tunnel TTL threshold, as shown in the IP multicast DVMRP tunnel 
summary display. You can change these values through menu options.

■

IP multicast interfaces and tunnels have similar characteristics, such as 
TTL threshold and metric. The characteristics of a tunnel do not have 
to match the characteristics of the interface on which it is configured.

■

You can define multiple tunnel end points on the same local routing 
interface in your system, but these tunnels must lead to different 
remote routing interfaces. 

Summary of Contents for CoreBuilder 9000

















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CoreBuilder 9000

Cabletron Systems SmartSwitch 9000 Installation Manual preview
SmartSwitch 9000
Brand: Cabletron Systems Pages: 18
IEI Technology EBC-3620 Quick Installation Manual preview
EBC-3620
Brand: IEI Technology Pages: 8
Avaya Advanced Gateway 2330 Regulatory Information preview
Advanced Gateway 2330
Brand: Avaya Pages: 72
Cisco TelePresence Server 7010 Installation Manual preview
TelePresence Server 7010
Brand: Cisco Pages: 204
Cisco TelePresence Server 7010 Hardware Installation And Maintenance Manual preview
TelePresence Server 7010
Brand: Cisco Pages: 287
Cisco CRS-1 - Carrier Routing System Router Administration Manual preview
CRS-1 - Carrier Routing System Router
Brand: Cisco Pages: 436
Rosewill RSV-X4000 User Manual preview
RSV-X4000
Brand: Rosewill Pages: 8
Rosewill RSV-L4412 User Manual preview
RSV-L4412
Brand: Rosewill Pages: 8
Keysight M9018A Startup Manual preview
M9018A
Brand: Keysight Pages: 52
Keysight Ixia IxOS XGS2 Series Getting Started Manual preview
Ixia IxOS XGS2 Series
Brand: Keysight Pages: 64
Jung JLA-e 15/30 G Operating Instructions Manual preview
JLA-e 15/30 G
Brand: Jung Pages: 196
AndyMark AM14U4 Battery Mount Installation preview
AM14U4
Brand: AndyMark Pages: 2

Brands by name

Popular brands

Load more brands