manualshive.com logo in svg

3Com CoreBuilder 3500, Implementation Manual, Page: 276 / 592

Share
Download
3Com CoreBuilder 3500 Implementation Manual Download Page 276

276

C

HAPTER

 11: I

NTERNET

 P

ROTOCOL

 (IP)

Port-based Routing

In the communications industry, Layer 3 devices have traditionally 
employed port-based routing: routed packets over interfaces that are 
associated with a 

single physical port

.

Figure 49 illustrates traditional routing:

1

The packet enters the switch.

2

The bridge or router determines that the packet belongs to a recognized 
routing protocol, so the packet is passed to the router. 

3

The router examines the destination network address and forwards the 
packet to the interface (port) that is connected to the destination 
subnetwork.

Figure 49   

Routing versus Bridging

Port-based routing is advantageous for networks or network segments 
whose emphasis is heavily on routing rather than bridging. 

1

Transmitting host

3

Destination host

Interfaces (ports)

Router

Bridge

2

Networks

Router vs. Bridge ?

Summary of Contents for CoreBuilder 3500

















































































































































































































































































































































































































































































































































































































Reviews:

No comments