3Com 3CR17450-91 Getting Started Manual Download Page 62

Page: 62 / 86

PPENDIX

A: S

AFETY

NFORMATION

tool. Keep the blanking plate and the fixings in a safe place. If you
remove the Module at any time, you must then replace the blanking
plate.

WARNING

: Fiber optic ports - optical safety

Never look at the transmit laser while it is powered on. Never look directly
at the fiber ports and fiber cable ends when they are powered on.

WARNING

Use of controls or adjustments of performance or

procedures other than those specified herein may result in hazardous
laser emissions.

L’information de Sécurité Importante

AVERTISSEMENT:

L'installation et la dépose de ce groupe doivent être

confiés à un personnel qualifié.

AVERTISSEMENT:

Si vous entassez l'unité Switch avec les unités

SuperStack

3 Hub, l'unité de la gamme des Switch 3870 doit être

installée en dessous des unités Hub plus étroites.

AVERTISSEMENT:

Vous devez mettre l’appareil à la terre (à la masse) ce

groupe.

AVERTISSEMENT:

Brancher l’unité à une source de courant mise à la

terre pour assurer la conformité aux normes de sécurité.

Class 1

LASER PRODUCT

Summary of Contents for 3CR17450-91























































































Search results

Summary of Contents for 3CR17450-91

Reviews:

Related manuals for 3CR17450-91

Brands by name

Popular brands

3Com 3CR17450-91, Getting Started Manual

Search results

Summary of Contents for 3CR17450-91

Reviews:

Related manuals for 3CR17450-91

Brands by name

Popular brands