manualshive.com logo in svg

3Com 3Com SuperStack 3 Switch 3800 Family, User Manual

Share
Download
3Com 3Com SuperStack 3 Switch 3800 Family User Manual Download Page 111

Displaying STP Settings

7-13

Sample output from the command is as follows:

3C16910:28 # sh stpd s0 po 5-8

Stpd: s0  Port: 8

PortId: 8008 Stp: ENABLED

Path Cost: 4

Port State: FORWARDING 

Topology Change Ack: FALSE

Port Priority: 128

Designated Root: 80:00:08:00:4e:2c:13:00 Designated Cost: 0

Designated Bridge: 80:00:08:00:4e:2c:13:00 

Designated Port Id: 8008

Stpd: s0

Port:  7

PortId: 8007 Stp: ENABLED

Path Cost: 4

Port State: FORWARDING

Topology Change Ack: FALSE

Port Priority: 128

Designated Root: 80:00:08:00:4e:2c:13:00Designated Cost: 0

Designated Bridge: 80:00:08:00:4e:2c:13:00 

Designated Port Id: 8007

Stpd: s0

Port:  6

PortId: 8006 Stp: ENABLED

Path Cost: 4

Port State: BLOCKING

Topology Change Ack: FALSE

Port Priority: 128

Designated Root: 80:00:08:00:4e:2c:13:00Designated Cost: 0

Designated Bridge: 80:00:08:00:4e:2c:13:00      

Designated Port Id: 8003

Stpd: s0

Port:  5

PortId: 8005 Stp: ENABLED

Path Cost: 4

Port State: FORWARDING

Topology Change Ack: FALSE

Port Priority: 128

Designated Root: 80:00:08:00:4e:2c:13:00Designated Cost: 0

Designated Bridge: 80:00:08:00:4e:2c:13:00 

Designated Port Id: 8005

SW3800.BK  Page 13  Tuesday, May 5, 1998  5:20 PM

Summary of Contents for 3Com SuperStack 3 Switch 3800 Family























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands