3Com 3C971-F ATMLINK User Manual Download

Page: 9 / 87

IGURES

1-1

3C971-F ATMLink PCI Adapter 1-1

2-1

Removing Expansion Slot Cover 2-3

2-2

Adapter Card Installed in Chassis 2-3

2-3

SC Duplex Connection 2-5

3-1

Network Settings Screen 3-5

3-2

Add Network Adapter 3-5

3-3

Selecting the Floppy Drive 3-6

3-4

Loading the 3C971-F Adapter Hardware Driver 3-7

3-5

PCI Adapter Setup 3-7

3-6

Configuring the Signaling Transport 3-9

3-7

Completed Network Settings 3-10

3-8

TCP/IP Configuration with Sample Entries 3-11

3-9

Reboot Prompt for Adapter Driver 3-14

3-10

LEC Configuration 3-15

3-11

LEC ATM Adapter Configuration 3-17

3-12

LECS/LES Reboot Prompt 3-20

3-13

Removing 3C971-F Adapter and Drivers 3-21

3-14

Confirming Adapter and Driver Removal 3-22

3-15

Network Settings After Driver Removal 3-22

3-16

Reboot Prompt for Removing Drivers 3-23

4-1

NetWare 4.1 Installation Options 4-3

4-2

NetWare Driver Options 4-3

4-3

Select Additional Driver 4-4

4-4

Currently Installed Drivers 4-4

4-5

Notes for Selecting a Drive 4-5

4-6

Selecting a Driver from the 3Com Diskette 4-5

4-7

SVC Driver Confirmation 4-6

4-8

Driver Protocols/Parameters Edit 4-6

4-9

Configuring TCP/IP Network Interface 4-8

Summary of Contents for 3C971-F ATMLINK
























































































Search results

Summary of Contents for 3C971-F ATMLINK

Reviews:

Related manuals for 3C971-F ATMLINK

Brands by name

Popular brands

3Com 3C971-F ATMLINK, User Manual

Search results

Summary of Contents for 3C971-F ATMLINK

Reviews:

Related manuals for 3C971-F ATMLINK

Brands by name

Popular brands