manualshive.com logo in svg

360 Yield 360 Y-DROP APACHE, Instruction Manual

Share
Download
360 Yield 360 Y-DROP APACHE Instruction Manual Download Page 11

INSTRUCTIONS 360 Y-DROP

APACHE

360YIELDCENTER.COM

All other trademarks are the property of 360 Yield Center, its affiliates and/or its licensors.  

©2016 360 Yield Center. All rights reserved. 

Figure 22

Figure 23

Figure 24

INSTALL SHIELDS AND  

RISER HOSES 

(CONTINUED)

 

 

Figure 22

 

 
 
 

 

 CAUTION:  Do NOT use a drill or impact driver  
for Steps 5 and 6.

 

Step 5

   Install two ½" screws (1).

 

Step 6

  Install two ¾" screws (2).

 

Step 7

  Install rubber washer (3) into the “Y”.

 

Figure 23

 

Step 8

   Install riser hose assembly (1) into the “Y”. 

 

Figure 24

 

Step 9

   Route riser hose assembly (1) as shown  

in Figure 24. 

 

Step 10

   Install the riser hose assembly to the  

OEM nozzle body.

 

Step 11

   Use 3 equally spaced plastic ties to  

secure the riser hose assembly.

   Repeat Steps 1-11 for the remaining  

360 Y-DROP Shields.

VI.

  INSTALLATION COMPLETE.

1

1

1

1

3

2

Summary of Contents for 360 Y-DROP APACHE












Reviews:

No comments

Brands by name

Popular brands

Load more brands