2
Copyright © 2015 Nortek Security & Control LLC
Step 3: Powering ON the PIR
With
the
battery
inserted
(see
press
and
release
the
switch
labeled
TAMPER.
It
takes
approximately
10
seconds
for
the
PIR
to
power
ON.
Mounting the PIR
There
are
two
methods
for
mounting
the
PIR:
or
.
For
both
methods,
always
mount
the
PIR
at
a
height
of
7.5
ft
(2.3
m).
Figure 3
PIR and Mounting Bracket Detail
Option A: Bracket Mounting
See
.
If
you
plan
to
mount
the
PIR
to
either
the
Plastic
Wall
Mount
or
Plastic
Corner
Mount,
you
must
first
attach
the
Plastic
Mounting
Bracket
to
the
PIR
backplate.
Step 1: Attaching the Plastic Mounting Bracket to the PIR
1
Remove
the
PIR
backplate.
2
Insert
the
two
stubs
on
the
Plastic
Mounting
Bracket
into
the
corresponding
holes
on
the
exterior
side
of
the
PIR
backplate.
3
On
the
interior
of
the
PIR
backplate
(see
use
the
Short
Phillips
Head
Screw
(provided)
to
secure
the
Plastic
Mounting
Bracket
to
the
backplate
4
Replace
the
PIR
backplate.
5
Reattach
the
screw
that
was
removed
earlier
to
the
bottom
of
the
PIR.
6
Continue
with
either
or
NOTE:
For
optimum
pet
immunity
when
using
the
Plastic
Mounting
Bracket,
ensure
that
the
PIR
is
mounted
to
the
wall
or
corner
with
NO
tilt
(see
).
Step 2: Wall Mounting Option
See
.
If
using
the
Plastic
Wall
Mount
(C),
do
the
following:
NOTE:
Ensure
that
you
have
attached
the
bracket
to
the
PIR
backplate
(see
1
On
the
intended
wall,
use
the
two
(2)
Plastic
Wall
Anchors
to
hang
the
Plastic
Wall
Mount
at
a
height
of
7.5
ft
(2.3
m).
2
Locate
the
barrel
end
of
the
Plastic
Mounting
Bracket.
Locate
the
barrel
end
of
the
Plastic
Mounting
Bracket
and
carefully
set
it
onto
the
ribbed
pin
of
the
Plastic
Wall
Mount
at
the
desired
angle
(see
on
).
3
From
the
topside
of
the
Plastic
Wall
Mount,
use
the
Short
Phillips
Head
Screw
with
Fender
(provided)
to
secure
the
mount
to
the
barrel
end
of
the
bracket.
Step 2: Corner Mounting Option
See
If
using
Plastic
Corner
Mount,
do
the
following:
NOTE:
Ensure
that
you
have
attached
the
bracket
to
the
PIR
backplate
(see
on
).
1
Use
the
two
(2)
Plastic
Wall
Anchors
to
hang
the
Plastic
Corner
Mount
at
a
height
of
7.5
ft
(2.3
m).
2
Locate
the
barrel
end
of
the
Plastic
Mounting
Bracket
and
carefully
set
it
onto
the
ribbed
pin
of
the
Plastic
Wall
Mount.
Ensure
that
you
set
it
at
the
desired
angle
(see
).
3
From
the
topside
of
the
Plastic
Wall
Mount,
use
the
Short
Phillips
Head
Screw
with
Fender
(provided)
to
secure
the
mount
to
the
barrel
end
of
the
bracket.
Option B: Direct-to-Wall Mounting
If
planning
to
mount
the
PIR
directly
to
a
wall,
use
the
built
‐
in
mounting
guides
on
interior
of
the
PIR
backplate
to
screw
the
backplate
into
the
wall.
1
Remove
the
PIR
backplate.
2
Use
the
two
(2)
Plastic
Wall
Anchors
to
screw
the
PIR
backplate
into
the
wall
at
a
height
of
7.5
ft
(2.3
m):
•
Wall
.
Use
the
wall
mounting
guides
(see
A
below).
•
Corner
Mount
.
Use
the
left
‐
or
right
‐
corner
mounting
guides
(see
B
below).
Figure 4
PIR Backplate—Direct-to-Wall Mounting Guides
A
PIR
B
Plastic
Mounting
Bracket
C
Plastic
Wall
Mount
D
Plastic
Corner
Mount
A
Wall
Mounting
Guides
(For
)
B
Corner
Mounting
Guides
(For
)
C
Wall
Mount
Bracket
Guide
(For
)
