2
Copyright © 2015 Nortek Security & Control
Figure 6.
Screw Moun ng Sensor Moun ng Plate
Removing Flood/Temperature Sensor from Mounting Plate
If Flood/Temperature Sensor needs to be removed from the wall (for changing out
ba ery), open sensor case (See Figures 2 and 3). Remove ba ery, then Press Down
on release tab with
fl
athead screwdriver and pull sensor UP.
Figure 7.
Removing Sensor from Wall/Moun ng Plate
Mounting Flood Probe
The Flood Probe must be mounted at
fl
oor level using the Probe Moun ng Plate
and screw (included) mount as shown in Figure 8.
Figure 8.
Moun ng Probe Moun ng Plate at Floor Line
Flood/Temperature Specifi cations
Opera ng Temperature:
32
°
to 120
°
F (0
°
to 49
°
C)
Opera ng Rel. Humidity:
5 to 95%, non-condensing
Opera ng Frequency:
345 MHz
Ba ery Type:
CR2 3V lithium ba ery
Projected Ba ery Life:
5 Years
REGULATORY INFORMATION
This equipment has been tested and found to comply with the limits for Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protec on against harmful interference in a residen al installa on. This equipment generates
and can radiate radio frequency energy and, if not installed and used in accordance with the
instruc ons, may cause harmful interference to radio communica ons. However, there is
no guarantee that interference will not occur in a par cular installa on. If this equipment
does cause harmful interference to radio or television recep on, which can be determined by
turning the equipment o
ff
and on, the user is encouraged to try to correct the interference by
one or more of the following measures.
Reorient or relocate the receiving antenna
Increase the separa on between the equipment and receiver
Connect the equipment into an outlet on a circuit di
ff
erent from that to which the receiver
is connected
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modi
fi
ca ons not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence.
Ľ
exploita on est autorisée aux deux condi ons suivantes: (1)
ľ
appareil ne doit pas produire de brouillage, et (2)
ľ
u lisateur de
ľ
appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est suscep ble
ď
en comprome re le
fonc onnement.
FCC COMPLIANCE STATEMENT
This device complies with FCC Rules and Regula ons as Part 15 devices as well as Industry
Canada license exempt RSS Rules and Regula ons. Opera on is subject to the following two
(2) condi ons: This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired opera on.
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects in material and
workmanship for two (2) years. This warranty extends only to wholesale customers who
buy direct from Nortek Security & Control LLC or through Nortek Security & Control normal
distribu on channels. Nortek Security & Control does not warrant this product to consumers.
Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty,
if any.
There are no obliga ons or liabili es on the part of Nortek Security & Control for consequen al
damages arising out of or in connec on with use or performance of this product or other
indirect damages with respect to loss of property, revenue, or pro
fi
t, or cost of removal,
installa on, or reinstalla on. All implied warran es for func onality, are valid only un l the
warranty expires. This Nortek Security &Control Warranty is in lieu of all other warran es
expressed or implied.
Nortek Security & Control LLC
1950 Camino Vida Roble, Suite 150
Carlsbad, CA 92008-6517 USA
For technical support in the USA and Canada:
855-2GIG-TECH (855-244-4832)
Email: [email protected]
Visit www.nortekcontrol.com for technical support hours of opera on
For technical support outside of the USA and Canada:
Visit dealer.2gig.com for a list of distributors in your region
10008993 A
SENSOR
MOUNTING
PLATE
FIRST
PUSH
SENSOR
ONTO
MOUNTING
PLATE
TABS
THEN
PUSH
UP
MOUNT SENSOR
MOUNTING PLATE
WITH SCREWS (INCLUDED)
WALL
MOUNT FLOOD
PROBE MOUNTING
PLATE AT FLOOR LINE
FLOOD PROBE
SCREW FASTENER
INSTALL FLOOD
PROBE TO MOUNTING
PLATE UNTIL IT “SNAPS”
INTO THE SIDE CLIP
SIDE CLIP
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,2GIG-FT1 TEMP FLOOD SENSOR - P/N: 10008993 A- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5000” X 11.000” - TOL. +/- 0.125”- SCALE: 1-1 - PAGE 2 OF 2- FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING
2GIG Flood & Temperature Control I Instruc on Manual
OPEN SENSOR
CASE AND REMOVE
BATTERY
PRESS
DOWN ON
TAB IN UPPER LEFT
CORNER WITH FLATHEAD
SCREWDRIVER
THEN
PUSH UP
ON
SENSOR CASE TO REMOVE
