B. Selecting the ringtone:
There are 36 programmable ringtones for
selection.
Press the Ringtone selector button to
change the ringtone.
Stop pressing this button when you have
reached the desired ringtone.
C. Adjusting ringtone volume:
Press the volume button until the desired
volume is set. There are 3 volume levels for
selection.
D. Pairing additional push buttons/receivers to the
doorbell system:
Up to 5 push buttons can be paired with one
receiver. You can also extend the wireless
doorbell system with any number of receivers.
This is only possible if the push button and
receiver are working on the same frequency.
Pair additional push buttons/receivers using the
same pairing process as described below:
The following pairing instructions are relevant
·
Always insert the battery using the correct
polarity to eliminate the danger of fire.
·
Keep old and new batteries away from children.
·
Old batteries should be properly disposed using
safe environmental practices.
·
Remove the batteries from the receiver and
push button if the doorbell system is not to be
used for an extended period of time.
4. Operation:
A. Selecting the notification mode:
The doorbell receiver can notify after the push
button has been pressed by playing a ringing
sound, flashing an LED, or ringing and flashing
an LED at the same time. These are referred to as
Sound, Flash, and Sound + Flash mode.
To select the notification mode, switch the
sound and flash switch to one of the following
positions:
Sound only mode Flash only mode
Sound + Flash mode
3. Power supply:
Battery-operated receiver: The receiver is powered
by 2 x AA batteries. Please insert the batteries
using the following procedure:
a) Press the buckle on the battery compartment
cover and remove the battery compartment
cover at the back of the receiver.
b) Insert the 2 x AA batteries using the correct
polarity to eliminate the danger of fire.
c) Reattach the battery compartment cover.
Plug in receiver: Please plug into a safety power
outlet.
Push button: The push button is powered by a 3V
battery (Type: CR2032). Please insert the battery
using the following procedure:
a) Insert a screwdriver into the small access port at
the bottom of the push button and remove the
push button’s back cover.
b) Insert the 3V battery (type CR2032) into the
battery compartment, making sure the battery
surface marked with a “+” is facing upwards.
c) Reinsert the back cover, making sure it is
securely closed to ensure IP protection.
Note:
If the performance of the push button deteriorates
or completely stops, the battery might be
exhausted. Please replace with another 3V type
CR2032 battery.
Weak batteries can greatly reduce the ringtone
volume of the receiver, please change the
batteries every 8-10 months.
Safety note:
For the plug-in receiver:
·
Please plug it into a safe power outlet
·
Do not expose the receiver to water spray or
water drops and do not place liquid-filled
objects such as vases or opened drink
containers on or near the receiver and the
outlet.
·
Unplug the receiver immediately if you sense a
burning smell or smoke. Have qualified
personnel check the receiver before using it
again.
·
Unplug the receiver from the outlet if the
doorbell system is not to be used for an
extended period of time.
For the battery-operated receiver and push button:
·
Weak battery can greatly reduce the ringtone of
the receiver, please replace with the same
voltage and type batteries every 8-10 months.
- 05 -
- 06 -
to receiver (SKU: O00QH-0504) and push button
(SKU: O00QH-0503).
Press the pairing button on the receiver.
Next press the push button. If pairing is
successful, the receiver should ring. It normally
takes about 10 seconds for the push button and
receiver to pair. If there is no pairing within 10
seconds, the receiver will exit the pairing mode.
Please try pairing again.
E. Re-pairing function:
If a receiver starts ringing even when the push
button hasn’t been pressed, or a push button
interferes with other receivers, it may be
necessary to wipe the current pairings and pair
again.
To reset the push buttons, you need to cut off
the power supply for the receiver and push
button.
Remove the battery from the push button and
unplug the receiver from the power outlet. Then
re-attach them to power after 30 seconds. You
can now pair the desired push buttons.
