ZyXEL Communications P-871H Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 101

background image

P-871H Series User’s Guide

Safety Warnings

3

Safety Warnings

For your safety, be sure to read and follow all warning notices and instructions.

• To reduce the risk of fire, use only No. 26 AWG (American Wire Gauge) or larger telecommunication

line cord.

• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high

voltage points or other risks. ONLY qualified service personnel can service the device. Please contact
your vendor for further information.

• Use ONLY the dedicated power supply for your device. Connect the power cord or power adaptor to

the right supply voltage (110V AC in North America or 230V AC in Europe).

• Do NOT use the device if the power supply is damaged as it might cause electrocution.
• If the power supply is damaged, remove it from the power outlet.
• Do NOT attempt to repair the power supply. Contact your local vendor to order a new power supply.
• Place connecting cables carefully so that no one will step on them or stumble over them. Do NOT

allow anything to rest on the power cord and do NOT locate the product where anyone can walk on
the power cord.

• If you wall mount your device, make sure that no electrical, gas or water pipes will be damaged.
• Do NOT install nor use your device during a thunderstorm. There may be a remote risk of electric

shock from lightning.

• Do NOT expose your device to dampness, dust or corrosive liquids.
• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.
• Make sure to connect the cables to the correct ports.
• Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.
• Do NOT store things on the device.
• Connect ONLY suitable accessories to the device.

«
...
2
3
4
5
6
...
»

Содержание P-871H Series






































































































Отзывы:

Нет отзывов

Похожие инструкции для P-871H Series

Linux USB?ADG?2

Бренд: Air 802 Страницы: 39

Бренд: PROLiNK Страницы: 10

Бренд: Intercel Страницы: 7

Бренд: CyberTAN Страницы: 6

Бренд: Black Box Страницы: 101

Бренд: Microsoft Страницы: 37

Бренд: Ebyte Страницы: 42

Бренд: Patton electronics Страницы: 19

Бренд: Jizhuo Technology Страницы: 13

ESTeem Horizon 216An

Бренд: EST Страницы: 104

Бренд: Dynex Страницы: 8

COMSPHERE 3810Plus

Бренд: Paradyne Страницы: 28

Бренд: Four-Faith Страницы: 47

Бренд: Adeunis RF Страницы: 25

Бренд: Adeunis RF Страницы: 40

Бренд: Adeunis RF Страницы: 77

Бренд: Telecom Страницы: 41

Бренд: US Robotics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды