manualshive.com logo in svg

ZyXEL Communications OLT2406, Руководство пользователя

Поделиться
Скачать
ZyXEL Communications OLT2406 Скачать руководство пользователя страница 637

OLT2406 User’s Guide

637

C

HAPTER

 89

MAC Forced Forwarding

89.1  Overview

This chapter lists the commands for activating/deactivating MAC Forced Forwarding and for setting it 
up in a VLAN interface.

89.2  MAC Forced Forwarding Commands

Use MACFF (MAC Forced Forwarding) to hide internal server information from hosts in the same subnet. 
The OLT intercepts a host’s ARP (Address Resolution Protocol) requests and forwards them to a pre-
defined gateway. The gateway routes or forwards traffic so hosts in the same subnet won’t know the 
internal server’s MAC addresses.

Here is an example showing packets forwarding from 

Host 1

 (192.168.1.11) to 

Host 2

 (192.168.1.12). In 

normal switch function, these two hosts can communication with each other directly, because they are 
in the same subnet. If MACFF is enabled, 

Host 1

 (192.168.1.11) will forward packets to 

Gateway

, and 

Gateway

 forwards the packets to 

Host 2

 (192.168.1.12).

Figure 287   

MACFF Application

Gateway

Host 1

Host 2

OLT

IP

: 192.168.1.11

IP

: 192.168.1.12

IP

: 192.168.1.254

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды