ZyXEL Communications OLT2406 Скачать руководство пользователя страница 485

Страница: 485 / 766

Chapter 66 Broadcast Storm Control

OLT2406 User’s Guide

485

66.3 Broadcast Storm Control Examples

Enable broadcast storm control on the OLT.

Disable broadcast storm control on the OLT.

Set broadcast storm control on a port (ge-5-1) which is active, to limit its broadcast type traffic with a
threshold of 999 packets per second.

storm-control counter <cr>

Enables storm control packet counting for the
specified port.

storm-control logging <cr>

Enables storm control packet logging for the
specified port.

no storm-control counter

Disables storm control packet counting for the
specified port.

no storm-control logging

Disables storm control packet logging for the
specified port.

Table 243 Broadcast Storm Control Commands (continued)

COMMAND

DESCRIPTION

OLT2406# configure

OLT2406(config)# storm-control

OLT2406(config)# no storm-control

OLT2406(config)# interface port-channel ge-5-1

OLT2406(config-interface)# broadcast-limit

OLT2406(config-interface)# broadcast-limit 999

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды

ZyXEL Communications OLT2406, Руководство пользователя

Результаты поиска

Содержание OLT2406

Отзывы:

Бренды по названию

Популярные бренды