manualshive.com logo in svg

ZyXEL Communications OLT2406, Руководство пользователя

Поделиться
Скачать
ZyXEL Communications OLT2406 Скачать руководство пользователя страница 271

OLT2406 User’s Guide

271

C

HAPTER

 31

ONT VoIP

31.0.1  ONT VoIP Profile

Use the 

GPON

 > 

ONT VoIP Profile 

screens to configure VoIP settings for the subscriber Optical Network 

Terminal (ONT) devices.

VoIP is the sending of voice signals over Internet Protocol. This allows you to make phone calls and send 
faxes over the Internet at a fraction of the cost of using the traditional circuit-switched telephone 
network. You can also use servers to run telephone service applications like PBX services and voice mail. 
Internet Telephony Service Provider (ITSP) companies provide VoIP service. 

Circuit-switched telephone networks require 64 kilobits per second (Kbps) in each direction to handle a 
telephone call. VoIP can use advanced voice coding techniques with compression to reduce the 
required bandwidth. 

31.0.2  What You Can Do

• Use the 

VoIP Common Profile

 screen (

Section 31.1 on page 272

) to configure general VoIP settings for 

ONTs.

• Use the 

VoIP SIP Profile

 screen (

Section 31.2 on page 275

) to configure ONT VoIP SIP settings.

• Use the 

VoIP Dial Plan Profile

 screen (

Section 31.3 on page 278

) to create dial plan profiles.

31.0.3  What You Need to Know

SIP

The Session Initiation Protocol (SIP) is an application-layer control (Signaling) protocol that handles the 
setting up, altering and tearing down of voice and multimedia sessions over the Internet.

SIP signaling is separate from the media for which it handles sessions. The media that is exchanged 
during the session can use a different path from that of the signaling. SIP handles telephone calls and 
can interface with traditional circuit-switched telephone networks.

SIP Identities

A SIP account uses an identity (Sometimes referred to as a SIP address). A complete SIP identity is called 
a SIP URI (Uniform Resource Identifier). A SIP account's URI identifies the SIP account in a way similar to 
the way an e-mail address identifies an e-mail account. The format of a SIP identity is SIP-Number@SIP-
Service-Domain.

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды