ZyXEL Communications OLT2406 Скачать руководство пользователя страница 262 | Manualshive

Страница: 262 / 766

ZyXEL Communications OLT2406 Скачать руководство пользователя страница 262

Chapter 29 PPPoE

OLT2406 User’s Guide

262

29.3.5 Option 82

Use this screen to append the Circuit ID and Remote ID to PPPoE discovery packets of a VLAN.

You can also use special characters to add

GPON Option

s (dynamic information) of an ONT to PPPoE

discovery packets from PPPoE clients on a per-vlan basis. You can determine the order of components
in your Circuid ID and Remote ID strings manually.

The OLT will get the

GPON Option

s (dynamic information) of the ONT(s) from traffic on the VLAN.

It’s recommended to use this screen for more flexibility in configuring Circuit and Remote ID information.
See

Table 101 on page 255

for more information.

Click the

Option 82

link in the

Intermediate Agent

screen to display the screen as shown.

Figure 159

Advanced Application > PPPoE > Intermediate Agent > Option 82

Apply

Click

Apply

to display the specified range of VLANs in the section below.

VID

This field displays the VLAN ID of each VLAN in the range specified above. If you configure the

*

VLAN, the settings are applied to all VLANs.

*

Use this row to make the setting the same for all VLANs. Use this row first and then make
adjustments on a VLAN-by-VLAN basis.

Changes in this row are copied to all the VLANs as soon as you make them.

Enabled

Select this option to turn on the PPPoE Intermediate Agent on a VLAN.

Circuit-id

Select this option to make the Circuit ID settings for a specific VLAN take effect.

Remote-id

Select this option to make the Remote ID settings for a specific VLAN take effect.

Apply

Click

Apply

to save your changes to the OLT’s run-time memory. The OLT loses these changes if it

is turned off or loses power, so use the

Save

link on the top navigation panel to save your

changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

Table 106 Advanced Application > PPPoE > Intermediate Agent > VLAN (continued)

LABEL

DESCRIPTION

«
...
260
261
262
263
264
...
»

Содержание OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды