ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 327 | Manualshive

Страница: 327 / 370

background image

Chapter 42 Syslog

MES3500 Series User’s Guide

327

Figure 214

Management > Syslog

The following table describes the labels in this screen.

42.3 Syslog Server Setup

Click

Management

>

Syslog

>

Syslog Server Setup

to view the screen as shown next. Use this

screen to configure a list of external syslog servers.

Table 157

Management > Syslog

LABEL

DESCRIPTION

Syslog

Select

Active

to turn on syslog (system logging) and then configure the syslog setting.

Logging Type

This column displays the names of the categories of logs that the device can generate.

Active

Select this option to set the device to generate logs for the corresponding category.

Facility

The log facility allows you to send logs to different files in the syslog server. Refer to the
documentation of your syslog program for more details.

Privilege

Select a command privilege level. The Switch will only generate logs for commands that have
a privilege level greater than or equal to the specified privilege level.

Apply Click

Apply

to save your changes to the Switch’s run-time memory. The Switch loses these

changes if it is turned off or loses power, so use the

Save

link on the top navigation panel to

save your changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

«
...
325
326
327
328
329
...
»

Содержание MES3500 Series



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MES3500 Series

AirPlus DWL-810

Бренд: D-Link Страницы: 25

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: TC Electronic Страницы: 174

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

IMACS Network Device

Бренд: Zhone Страницы: 114

Бренд: AirTies Страницы: 28

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

Бренд: MAKER MADE Страницы: 40

Бренд: Vivotek Страницы: 13

Barricade SMC7908VoWBRA2

Бренд: SMC Networks Страницы: 2

Бренд: Paradyne Страницы: 1

Бренд: Westermo Страницы: 18

Бренд: Microview Страницы: 21

Бренд: Edimax Страницы: 86

Бренд: Exinda Страницы: 623

Бренд: CommScope Страницы: 30

3-Slot 24 Fast Ethernet + 2 Gigabit L2 Managed Switch with Redundant Power

Бренд: Blackbox Страницы: 255

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды