ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 297

Страница: 297 / 370

Chapter 39 Maintenance

MES3500 Series User’s Guide

297

39.5 Firmware Upgrade

Make sure you have downloaded (and unzipped) the correct model firmware and version to your
computer before uploading to the device.

Firmware is uploaded to the current image. See

Section 39.9 on page 300

for more information

about images and uploading firmware to a different image.

Be sure to upload the correct model firmware as uploading the wrong
model firmware may damage your device.

Click

Management

Maintenance

Firmware Upgrade

to view the screen as shown next.

Figure 190

Management > Maintenance > Firmware Upgrade

Type the path and file name of the firmware file you wish to upload to the Switch in the

File Path

text box or click

Browse

to locate it. Select the

Rebooting

check box if you want to reboot the

Switch and apply the new firmware immediately. (Firmware upgrades are only applied after a
reboot). Click

Upgrade

to load the new firmware.

After the firmware upgrade process is complete, see the

System Info

screen to verify your current

firmware version number.

39.6 Restore a Configuration File

Restore a previously saved configuration from your computer to the Switch using the

Restore

Configuration

screen.

Figure 191

Management > Maintenance > Restore Configuration

Type the path and file name of the configuration file you wish to restore in the

File Path

text box or

click

Browse

to locate it. After you have specified the file, click

Restore

. "config" is the name of

Содержание MES3500 Series



















































































































































































































































































































































































Результаты поиска

Содержание MES3500 Series

Отзывы:

Похожие инструкции для MES3500 Series

Бренды по названию

Популярные бренды

ZyXEL Communications MES3500 Series, Руководство пользователя

Результаты поиска

Содержание MES3500 Series

Отзывы:

Похожие инструкции для MES3500 Series

Бренды по названию

Популярные бренды