ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 262 | Manualshive

Страница: 262 / 370

background image

Chapter 33 Error Disable

MES3500 Series User’s Guide

262

Figure 158

Advanced Application > Errdisable > Errdisable Detect

The following table describes the labels in this screen.

33.7 Error-Disable Recovery Configuration

Use this screen to configure the Switch to automatically undo an action after the error is gone. Click
the

Click Here

link

next to

Errdisable Recovery

in the

Advanced Application > Errdisable

screen to display the screen as shown.

Table 117

Advanced Application > Errdisable > Errdisable Detect

LABEL

DESCRIPTION

Cause

This field displays the types of control packet that may cause CPU overload.

*

Use this row to make the setting the same for all entries. Use this row first and then make
adjustments to each entry if necessary.

Note: Changes in this row are copied to all the entries as soon as you make them.

Active

Select this option to have the Switch detect if the configured rate limit for a specific control
packet is exceeded and take the action selected below.

Mode

Select the action that the Switch takes when the number of control packets exceed the rate
limit on a port, set in the

Advanced Application > Errdisable > CPU protection

screen.

•

inactive-port

- The Switch disables the port on which the control packets are received.

•

inactive-reason

- The Switch drops all the specified control packets on the port.

•

rate-limitation

- The Switch drops the additional control packets the port has to handle

in every one second.

Apply

Click

Apply

to save your changes to the Switch’s run-time memory. The Switch loses these

changes if it is turned off or loses power, so use the

Save

link on the top navigation panel to

save your changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

«
...
260
261
262
263
264
...
»

Содержание MES3500 Series



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MES3500 Series

DHI-NVR5224-24P-4KS2

Бренд: Dahua Страницы: 24

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP Страницы: 14

Бренд: Lanpro Страницы: 5

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 4

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

SINUS H PROFInet

Бренд: Enertronica Santerno Страницы: 34

Бренд: THOMSON Страницы: 212

Бренд: Belkin Страницы: 2

InnoMedia MTA 3328-2R

Бренд: VoiceLine Страницы: 18

Бренд: Neousys Technology Страницы: 39

Бренд: RadioSPECTRAL Страницы: 2

Бренд: ActiveEye Страницы: 35

Бренд: Tripp Lite Страницы: 3

Бренд: Supermicro Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды