ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 206 | Manualshive

Страница: 206 / 370

background image

Chapter 26 AAA

MES3500 Series User’s Guide

206

26.2.2 Server Setup

Use this screen to configure your server settings. See

Section 26.1.2 on page 204

more information on servers. Click on the

Server Setup

link in the

Authentication and Accounting

screen to view the screen as shown.

Delete

Check this box if you want to remove an existing RADIUS server entry from the Switch. This
entry is deleted when you click

Apply

.

Apply

Click

Apply

to save your changes to the Switch’s run-time memory. The Switch loses these

changes if it is turned off or loses power, so use the

Save

link on the top navigation panel to

save your changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

Accounting
Server

Use this section to configure your RADIUS accounting server settings.

Timeout

Specify the amount of time in seconds that the Switch waits for an accounting request
response from the RADIUS accounting server.

Index

This is a read-only number representing a RADIUS accounting server entry.

IP Address

Enter the IP address of an external RADIUS accounting server in dotted decimal notation.

UDP Port

The default port of a RADIUS accounting server for accounting is

1813

. You need not change

this value unless your network administrator instructs you to do so.

Shared Secret

Specify a password (up to 32 alphanumeric characters) as the key to be shared between the
external RADIUS accounting server and the Switch. This key is not sent over the network.
This key must be the same on the external RADIUS accounting server and the Switch.

Note that as you type a password, the screen displays an asterisk (*) for each character you
type.

Delete

Check this box if you want to remove an existing RADIUS accounting server entry from the
Switch. This entry is deleted when you click

Apply

.

Apply

Click

Apply

to save your changes to the Switch’s run-time memory. The Switch loses these

changes if it is turned off or loses power, so use the

Save

link on the top navigation panel to

save your changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

Table 79

Advanced Application > AAA > RADIUS Server Setup (continued)

LABEL

DESCRIPTION

«
...
204
205
206
207
208
...
»

Содержание MES3500 Series



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MES3500 Series

Бренд: D-Link Страницы: 100

Бренд: D-Link Страницы: 134

Бренд: D-Link Страницы: 187

Бренд: D-Link Страницы: 225

Бренд: D-Link Страницы: 31

Бренд: D-Link Страницы: 35

DES-1016D - Switch

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 107

AirPlusXtremeG DI-624

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 48

Бренд: Habitat Страницы: 48

Netlink FRX8000

Бренд: Cabletron Systems Страницы: 94

MMAC-Plus 9E423-24

Бренд: Cabletron Systems Страницы: 10

MMAC-Plus 9A128-01

Бренд: Cabletron Systems Страницы: 22

Spectrum EMM-E6

Бренд: Cabletron Systems Страницы: 2

SmartSTACK ELS100-24TXG

Бренд: Cabletron Systems Страницы: 112

Бренд: Cabletron Systems Страницы: 86

Бренд: Cabletron Systems Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды