ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 370

background image

MES3500 Series User’s Guide

134

C

H A P T E R

1 4

Bandwidth Control

This chapter shows you how you can cap the maximum bandwidth using the

Bandwidth Control

screen.

14.1 Bandwidth Control Overview

Bandwidth control means defining a maximum allowable bandwidth for incoming and/or out-going
traffic flows on a port.

14.1.1 CIR and PIR

The Committed Information Rate (CIR) is the guaranteed bandwidth for the incoming traffic flow on
a port. The Peak Information Rate (PIR) is the maximum bandwidth allowed for the incoming traffic
flow on a port when there is no network congestion.

The CIR and PIR should be set for all ports that use the same uplink bandwidth. If the CIR is
reached, packets are sent at the rate up to the PIR. When network congestion occurs, packets
through the ingress port exceeding the CIR will be marked for drop.

Note: The CIR should be less than the PIR.

Note: The sum of CIRs cannot be greater than or equal to the uplink bandwidth.

14.2 Bandwidth Control Setup

Click

Advanced Application

>

Bandwidth Control

in the navigation panel to bring up the screen

as shown next.

«
...
132
133
134
135
136
...
»

Содержание MES3500 Series



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MES3500 Series

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: JCG Страницы: 2

Бренд: Hawking Страницы: 2

Бренд: AMX Страницы: 2

Бренд: B&B Electronics Страницы: 2

DiamondLink 3201

Бренд: Patton Страницы: 12

Ezi-SERVOII EtherCAT TO

Бренд: Fastech Страницы: 108

Бренд: Global411 Страницы: 15

Бренд: ZyXEL Communications Страницы: 79

Бренд: LevelOne Страницы: 26

NVR41-4KS2 Series

Бренд: Dahua Страницы: 452

ReadyNAS 3220 Series

Бренд: NETGEAR Страницы: 4

EdgeRouter ER-8

Бренд: Ubiquiti Страницы: 20

Бренд: Paradyne Страницы: 108

Бренд: Comelit Страницы: 140

TigerSwitch 100 SMC6924VF

Бренд: SMC Networks Страницы: 174

Бренд: Pro-Nets Technology Corporation Страницы: 48

Бренд: Intellinet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды