ZyXEL Communications MAX-200M1 Series Скачать руководство пользователя страница 79

Страница: 79 / 258

ZyXEL MAX-200M1 Series User’s Guide

Chapter 7 WAN Setup

Figure 44

Network > WAN > Advanced

The following table describes the labels in this screen.

Table 18

Network > WAN > Advanced

LABEL

DESCRIPTION

DNS Servers

First, Second and

Third DNS Server

Select

Obtained

from ISP

if your ISP dynamically assigns DNS server

information (and the ZyXEL Device's WAN IP address). Use the drop-down

list box to select a DNS server IP address that the ISP assigns in the field to

the right.
Select

UserDefined

if you have the IP address of a DNS server. Enter the

DNS server's IP address in the field to the right. If you chose

UserDefined

but leave the IP address set to 0.0.0.0,

UserDefined

changes to

None

after

you click

Apply

. If you set a second choice to

UserDefined

, and enter the

same IP address, the second

UserDefined

changes to

None

after you click

Apply

Select

None

if you do not want to configure DNS servers. You must have

another DHCP sever on your LAN, or else the computers must have their

DNS server addresses manually configured. If you do not configure a DNS

server, you must know the IP address of a computer in order to access it.

RIP & Multicast Setup

RIP Direction

Select the RIP direction from

None

Both

In Only

and

Out Only

RIP Version

Select the RIP version from

RIP-1

RIP-2B

and

RIP-2M

Multicast

IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to

establish membership in a multicast group. The ZyXEL Device supports both

IGMP version 1 (

IGMP-v1

) and

IGMP-v2

. Select

None

to disable it.

Windows Networking

(NetBIOS over TCP/IP)

NetBIOS (Network Basic Input/Output System) are TCP or UDP packets that

enable a computer to connect to and communicate with a LAN. For some dial-

up services such as PPPoE or PPTP, NetBIOS packets cause unwanted calls.

However it may sometimes be necessary to allow NetBIOS packets to pass

through to the WAN in order to find a computer on the WAN.

Содержание MAX-200M1 Series



































































































































































































































































Результаты поиска

Содержание MAX-200M1 Series

Отзывы:

Похожие инструкции для MAX-200M1 Series

Бренды по названию

Популярные бренды

ZyXEL Communications MAX-200M1 Series, Руководство пользователя

Результаты поиска

Содержание MAX-200M1 Series

Отзывы:

Похожие инструкции для MAX-200M1 Series

Бренды по названию

Популярные бренды