ZyXEL Communications IES-1248-51 Скачать руководство пользователя | Manualshive

Страница: 6 / 385

background image

IES-1248-51 User’s Guide

6

ZyXEL Limited Warranty

ZyXEL Limited Warranty

ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials
or workmanship for a period of up to two years from the date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or
materials, ZyXEL will, at its discretion, repair or replace the defective products or components without
charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or
components to proper operating condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL.
This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act
of God, or subjected to abnormal working conditions.

Note

Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This
warranty is in lieu of all other warranties, express or implied, including any implied warranty of
merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for
indirect or consequential damages of any kind to the purchaser.

To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material
Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit
be insured when shipped. Any returned products without proof of purchase or those with an out-dated
warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts
and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address,
Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary
from country to country.

Note:

Register your product online to receive e-mail notices of firmware upgrades and

information at www.zyxel.com for global products, or at www.us.zyxel.com for North American
products.

«
...
4
5
6
7
8
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: ICP DAS USA Страницы: 38

Бренд: Edimax Страницы: 44

Бренд: Novatel Страницы: 28

Бренд: LOVATO ELECTRIC Страницы: 7

Бренд: GDI Страницы: 49

Бренд: Thermo Scientific Страницы: 37

DIVA T/A ISDN Modem

Бренд: Eicon Networks Страницы: 146

Бренд: Kasda Страницы: 35

Бренд: Whirlwind Страницы: 16

Бренд: Terayon Страницы: 24

Бренд: Technicolor Страницы: 28

MediaAccess TC8717T

Бренд: Technicolor Страницы: 84

Бренд: Telecom Страницы: 41

Бренд: B+B SmartWorx Страницы: 2

EZ Connect SMC8002CM-US

Бренд: SMC Networks Страницы: 2

EZ Connect SMC8004CM

Бренд: SMC Networks Страницы: 2

Бренд: Radio Shack Страницы: 20

Бренд: iiNet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды