ZyXEL Communications IES-1248-51 страница 56 Скачать руководство пользователя | Manualshive

Страница: 56 / 385

background image

IES-1248-51 User’s Guide

56

Chapter 4 MDF Connections

• Use a punch-down tool to seat telephone lines into MDF blocks.
• Multiple upper and lower MDF port connections are shown as one line in the following

figures.

4.3 Telco-50 Cables

Telco-50 cables are used for data and voice applications with MDFs (Main Distribution
Frame), patch panels and distribution boxes. They can also be used as extension cables. Telco-
50 cables are made up of 25 twisted-pair copper wires.

Connect a Telco-50 connector to one end of the cable (see

Appendix C on page 375

assignments) and connect the other end directly to an MDF; alternatively attach RJ-11
connectors and connect directly to DSL modem(s).

Figure 15

Telco-50 Cable with RJ-11 Connectors

4.4 Telco-50 Connections

The internal DSL splitters separate the voice signals from the DSL signals. They feed the DSL
signals to the IES-1248-51 and divert the voice signals to the

CO

Telco-50 connectors.

Connect the

CO

Telco-50 connectors to the PBX or PSTN/ISDN switch.

Connect the

USER

Telco-50 connectors to the subscribers’ telephone wiring. In most multi-

tenant unit applications, the

USER

pins connect to the subscribers’ telephone wiring via Main

Distribution Frame (MDF).

«
...
54
55
56
57
58
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: Paradyne Страницы: 2

Бренд: U.S. Converters Страницы: 22

Бренд: Ubee Страницы: 80

Бренд: Sierra Wireless Страницы: 24

Бренд: Apantac Страницы: 1

Бренд: Telit Wireless Solutions Страницы: 74

Zlinx Xtreme ZXT24-RM

Бренд: B&B Electronics Страницы: 163

Бренд: Fargo Страницы: 17

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 58

Digital Business System

Бренд: Panasonic Страницы: 87

Бренд: Panasonic Страницы: 135

Бренд: Sagem Страницы: 36

Бренд: Hawking Страницы: 16

Hotwire 6310 MVL

Бренд: Paradyne Страницы: 17

Бренд: Ebyte Страницы: 39

Бренд: Paradyne Страницы: 4

Бренд: Four-Faith Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды