ZyXEL Communications IES-1248-51 Скачать руководство пользователя | Manualshive

Страница: 335 / 385

background image

IES-1248-51 User’s Guide

Chapter 49 ADSL Commands

335

This command configures settings and thresholds that define when the IES-1248-51 is to send
an alarm trap and generate a syslog entry.

Configure alarm profiles first and then use the

alarmprofile map

command to set the IES-

1248-51 to use them with specific ADSL ports.

The following example sets an alarm profile named

SESalarm

that has the IES-1248-51 send

an alarm trap and generate a syslog whenever the upstream connection’s number of severely
errored seconds exceeds three within a 15 minute period.

<atuc ess>
<atur ess>

=

The number of Errored Seconds that are permitted to occur
within 15 minutes.

<atuc fast
rateup> <atur
fast rateup>

=

A rate in kilobits per second (kbps). If a fast mode connection’s
upstream transmission rate increases by more than this number,
then a trap is sent.

<atuc
interleave
rateup> <atur
interleave
rateup>

=

A rate in kilobits per second (kbps). If an interleave mode
connection’s upstream transmission rate increases by more than
this number, then a trap is sent.

<atuc fast
ratedown> <atur
fast ratedown>

=

A rate in kilobits per second (kbps). If a fast mode connection’s
downstream transmission rate decreases by more than this
number, then a trap is sent.

<atuc
interleave
ratedown> <atur
interleave
ratedown>

=

A rate in kilobits per second (kbps). If an interleave mode
connection’s upstream transmission rate decreases by more than
this number, then a trap is sent.

<init fail
enable>

=

“1” sets the profile to trigger an alarm for an initialization
failures trap. “2” sets the profile to not trigger an alarm for an
initialization failures trap.

<atuc fail
fast>

=

The number of failed fast retrains that are permitted to occur
within 15 minutes.

<atuc ses>
<atur ses>

=

The number of Severely Errored Seconds that are permitted to
occur within 15 minutes.

<atuc uas>
<atur uas>

=

The number of UnAvailable Seconds that are permitted to occur
within 15 minutes.

Figure 224

Alarm Profile Set Command Example

ras> adsl alarmprofile set SESalarm 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 3
0 0 0

«
...
333
334
335
336
337
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: Ebyte Страницы: 20

Бренд: Ebyte Страницы: 31

Бренд: ADTRAN Страницы: 57

MultiModem CMDA MTCBA-C1X

Бренд: Multitech Страницы: 17

Бренд: Best Data Products Страницы: 41

Бренд: NetComm Страницы: 1

Бренд: Sangamo Страницы: 66

Бренд: Farallon Страницы: 162

Бренд: LG Страницы: 17

Бренд: Zte Страницы: 36

SMC EZ Connect SMC70032AE

Бренд: SMC Networks Страницы: 2

7804WBRB - FICHE TECHNIQUE

Бренд: SMC Networks Страницы: 2

7401BRA - FICHE TECHNIQUE

Бренд: SMC Networks Страницы: 2

SMC EZ Connect SMC70032AE

Бренд: SMC Networks Страницы: 58

Barricade SMC7904BRA2

Бренд: SMC Networks Страницы: 126

Бренд: Microflex Страницы: 10

Donatello Memory ISDN Modem

Бренд: Digicom Страницы: 1

Бренд: Digi Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды