ZyXEL Communications IES-1248-51 Скачать руководство пользователя | Manualshive

Страница: 263 / 385

background image

IES-1248-51 User’s Guide

Chapter 42 IEEE 802.1Q Tagged VLAN Commands

263

C

H A P T E R

42

IEEE 802.1Q Tagged VLAN

Commands

This chapter describes the IEEE 802.1Q Tagged VLAN commands.

42.1 Introduction to VLANs

See

Chapter 19 on page 147

for more background information on VLANs.

42.2 IEEE 802.1Q Tagging Types

There are two kinds of tagging:

• Explicit Tagging

A VLAN identifier is added to the frame header that identifies the source VLAN.

• Implicit Tagging

The MAC (Media Access Control) number, the port or other information is used to identify the
source of a VLAN frame.

The IEEE 802.1Q Tagged VLAN uses both explicit and implicit tagging.

It is important for the IES-1248-51 to determine what devices are VLAN-aware and VLAN-
unaware so that it can decide whether to forward a tagged frame (to a VLAN-aware device) or
first strip the tag from a frame and then forward it (to a VLAN-unaware device).

42.3 Filtering Databases

A filtering database stores and organizes VLAN registration information useful for switching
frames to and from the IES-1248-51. A filtering database consists of static entries (Static
VLAN or SVLAN table).

42.3.1 Static Entries (SVLAN Table)

Static entry registration information is added, modified and removed by administrators only.

«
...
261
262
263
264
265
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: Digi Страницы: 252

Бренд: Alcatel Страницы: 33

Бренд: Hal Communications Страницы: 30

AC/DC-POWERED USB HUB 4x USB 2.0

Бренд: WATSON Страницы: 6

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 4

COMSPHERE 3920PLUS Series

Бренд: Paradyne Страницы: 356

COMSPHERE 3920PLUS Series

Бренд: Paradyne Страницы: 2

Бренд: Packet One Страницы: 50

Бренд: PROLiNK Страницы: 10

USB ADSL Modem Hurricane Series

Бренд: PROLiNK Страницы: 21

Бренд: Spytec Страницы: 12

Direcway DW6000

Бренд: Hughes Страницы: 76

HomeConnect 3CR29223

Бренд: 3Com Страницы: 1

Impact External ISDN Modem

Бренд: 3Com Страницы: 6

Бренд: IBM Страницы: 82

Бренд: ERE Wireless Страницы: 20

Бренд: NETGEAR Страницы: 292

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды