ZyXEL Communications IES-1248-51 страница 218 Скачать руководство пользователя | Manualshive

Страница: 218 / 385

background image

IES-1248-51 User’s Guide

218

Chapter 35 Diagnostic

35.2.1 Log Messages

The following table lists and describes the system log messages.

Table 65

Log Messages

LOG MESSAGE

TYPE

DESCRIPTION

ADSL <port> Link
Up(SN=<seq no>): <ds
rate>/<us rate>!
or
ADSL Link Info: NM:<ds
NM>/<us NM>!

INFO

An ADSL port established a connection.
<port> - port number
<seq no> - sequence number of the connection
<ds rate> - downstream rate
<us rate> - upstream rate
<us NM> - upstream noise margin
<ds NM> - downstream noise margin

ADSL <port> Link
Down(SN=<seq no>)!

WARN

An ADSL port lost its connection.
<port> - port number
<seq no> - sequence number of the connection

Session Begin!

INFO

A console, telnet or FTP session has begun (see the

<process> field for the type of session).

Session End!

INFO

A console telnet or FTP session has terminated (see the

<process> field for the type of session).

Incorrect Password!

WARN

Someone attempted to use the wrong password to start a

console, telnet or FTP session (see the <process> field for the

type of session).

Received Firmware
Checksum Error!

WARN

A checksum error was detected during an attempted FTP

firmware upload.

Received Firmware Size
too large!

WARN

The file size was too large with an attempted FTP firmware

upload.

Received Firmware
Invalid!

WARN

Someone attempted to upload a firmware file with a wrong

identity via FTP.

Received File <file>! INFO

A file was uploaded to the IES-1248-51 by FTP.
<file> - received file’s name

THERMO OVER
TEMPERATURE: dev:<id>
threshold:<threshold>(
degree C)
value:<temp>(degree
C)!

WARN

The temperature was too high at one of the temperature

sensors.
<id> -
  0: sensor near the ADSL chipset
  1: sensor near the CPU
  2: thermal sensor chip itself
<threshold> - threshold temperature
<temp> - temperature when the entry was logged

THERMO OVER
TEMPERATURE released:
dev:<id>
threshold:<threshold>(
degree C)
value:<temp>(degree
C)!

INFO

The temperature at one of the temperature sensors has come

back to normal.
<id>
  0: sensor near the ADSL chipset
  1: sensor near the CPU
  2: thermal sensor chip itself
<threshold> - threshold temperature
<temp> - temperature when the entry was logged

«
...
216
217
218
219
220
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: Comtech EF Data Страницы: 206

Бренд: NetComm Страницы: 28

Бренд: Zte Страницы: 2

Бренд: Kasda Страницы: 35

Бренд: Javad Страницы: 36

Бренд: Javad Страницы: 56

Бренд: NETGEAR Страницы: 28

Бренд: NETGEAR Страницы: 29

Бренд: NETGEAR Страницы: 198

Бренд: AirLive Страницы: 81

dishNET HT 1000

Бренд: Hughes Страницы: 8

Barricade SMC7904BRB2

Бренд: SMC Networks Страницы: 2

7901BRA - FICHE TECHNIQUE

Бренд: SMC Networks Страницы: 2

Бренд: Racal-Vadic Страницы: 98

Бренд: Zhone Страницы: 14

Бренд: Zapp Страницы: 48

Бренд: Zte Страницы: 12

Бренд: Hamlet Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды