manualshive.com logo in svg

ZyXEL Communications IES-1248-51, Руководство пользователя

Поделиться
Скачать
ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 201

IES-1248-51 User’s Guide

Chapter 32 Static Routing

201

C

H A P T E R

32

Static Routing

This chapter shows you how to configure the static routing function.

Static routes tell the IES-1248-51 how to forward the IES-1248-51’s own IP traffic when you 
configure the TCP/IP parameters manually. This is generally useful for allowing management 
of the device from a device with an IP address on a different subnet from that of the device’s 
IP address (remote management).

To open this screen, click 

Routing Protocol

, 

Static Routing

.

Figure 104   

Static Routing

The following table describes the labels in this screen.

Table 57   

Static Routing

LABEL

DESCRIPTION

Use this section to create a new static route.

Name

Type a name to identify this static route. Use up to 31 ASCII characters. Spaces 

and tabs are not allowed.

Destination IP 

Address

This parameter specifies the IP network address of the final destination. Routing 

is always based on network number. If you need to specify a route to a single 

host, use a subnet mask of 255.255.255.255 in the subnet mask field to force 

the network number to be identical to the host ID.

IP Subnet Mask

Enter the subnet mask for this destination.

Gateway IP Address Enter the IP address of the gateway. The gateway is an immediate neighbor of 

your device that will forward the packet to the destination. The gateway must be 

a router on the same segment as your device.

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды