ZyXEL Communications IES-1248-51 страница 179 Скачать руководство пользователя | Manualshive

Страница: 179 / 385

background image

IES-1248-51 User’s Guide

Chapter 27 DHCP Relay

179

The following table describes the labels in this screen.

Table 44

DHCP Relay

LABEL

DESCRIPTION

Enable DHCP Relay: Enable DHCP relay to have the IES-1248-51 relay DHCP requests to a DHCP

server and the server’s responses back to the clients.

Relay Mode

Specify how the IES-1248-51 relays DHCP requests.

Auto

- The IES-1248-51 routes DHCP requests to the active server for each

VLAN.

Both

- The IES-1248-51 routes DHCP requests to the primary and secondary

server for each VLAN, regardless of which one is active.

Enable Option82

Sub-option1

Enable DHCP relay info to have the IES-1248-51 add the originating port

numbers to DHCP requests that it relays to a DHCP server.

Sub-option1 (Circuit

ID)

Use this field to specify up to 23 ASCII characters of additional information for

the IES-1248-51 to add to the DHCP requests that it relays to a DHCP server.
Examples of information you could add would be the chassis number of the IES-

1248-51 or the ISP’s name.

Enable Option82

Sub-option2

Enable DHCP relay info to have the IES-1248-51 add the sub-option 2 (Remote

ID) to DHCP requests that it relays to a DHCP server.

Sub-option2

(Remote ID)

Use this field to specify up to 23 ASCII characters of additional information for

the IES-1248-51 to add to the DHCP requests that it relays to a DHCP server.

Apply

Click

Apply

to save your changes to the IES-1248-51’s volatile memory. The

IES-1248-51 loses these changes if it is turned off or loses power, so use the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

VLAN ID

Enter the ID of the VLAN served by the specified DHCP relay(s). Enter 0 to set

up the IP address(es) of the default DHCP relay(s).

Primary Server IP

Enter the IP address of one DHCP server to which the switch should relay

DHCP requests for the selected VLAN.

Secondary Server IP Enter the IP address of a second DHCP server to which the switch should relay

DHCP requests for the selected VLAN. Enter 0.0.0.0 if there is only one DHCP

relay for the selected VLAN.

Active Server

This field has no effect if the

Relay Mode

is

Both

. If the

Relay Mode

is

Auto

,

select which DHCP server (the primary one or the secondary one) to which the

IES-1248-51 should relay DHCP requests for the selected VLAN.

Apply

Click

Apply

to save your changes to the IES-1248-51’s volatile memory. The

IES-1248-51 loses these changes if it is turned off or loses power, so use the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

Server List

This section lists the DHCP servers that are already set up for each VLAN. An

asterisk in parentheses (*) indicates which DHCP server is active for each

VLAN.

Index

This is a sequential value, and it is not associated with any entry. The entries are

sorted by VLAN ID.

VLAN ID

This field displays the ID of the VLAN served by the specified DHCP relay(s).

Primary Server IP

This field displays the IP address of one DHCP server to which the switch should

relay DHCP requests.

«
...
177
178
179
180
181
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IES-1248-51

Бренд: Comtrend Corporation Страницы: 10

Бренд: Connectland Страницы: 18

Бренд: SURFboard Страницы: 13

Бренд: Ubee Страницы: 22

Бренд: Ovation Страницы: 19

Бренд: Toshiba Страницы: 18

PCX1100 - DOCSIS Cable Modem

Бренд: Toshiba Страницы: 21

Бренд: Toshiba Страницы: 22

Бренд: Toshiba Страницы: 22

Бренд: Toshiba Страницы: 22

DOCSIS DAZ8820F

Бренд: Toshiba Страницы: 22

Бренд: Toshiba Страницы: 53

Бренд: Pacific Crest Страницы: 30

Бренд: HORNER Страницы: 40

Бренд: Hughes Network Страницы: 63

Donatello Memory ISDN Modem

Бренд: Digicom Страницы: 1

Бренд: Digi Страницы: 3

Connect WAN 3G IA

Бренд: Digi Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды