ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 128

Страница: 128 / 385

IES-1248-51 User’s Guide

128

Chapter 17 xDSL Profiles Setup

The following table describes the labels in this screen.

Table 22

Port Profile

LABEL

DESCRIPTION

VC Profile

Click

VC Profile

to open the

VC Profile

screen where you can configure virtual

channel profiles (see

Section 17.5 on page 133

Alarm Profile

Click

Alarm Profile

to open the

Alarm Profile

screen where you can configure

limits that trigger an alarm when exceeded (see

Section 17.6 on page 135

)

IGMP Filter Profile

Click

IGMP Filter Profile

to open the

IGMP Filter Profile

screen where you can

configure IGMP multicast filter profiles (see

Section 17.8 on page 138

Index

This is the port profile index number.

Name

These are the names of individual profiles. The DEFVAL profile always exists

and all of the DSL ports have it assigned to them by default. You can use up to

31 ASCII characters; spaces are not allowed.

Latency Mode

This is the ADSL latency mode (

Fast

Interleave

) for the ports that belong to

this profile.

Down/Up Stream

Rate (kbps)

These are the maximum downstream and upstream transfer rates for the ports

that belong to this profile.

Select
Modify

Select a profile’s

Select

radio button and click

Modify

to edit the profile.

Select
Delete

Select a profile’s

Select

radio button and click

Delete

to remove the profile.

The rest of the screen is for profile configuration.

Name

When editing a profile, this is the name of this profile. When adding a profile,

type a name (up to 31 characters) for the profile.

Latency Mode

This field sets the ADSL latency mode for the ports that belong to this profile.
Select

Fast

mode to use no interleaving and have faster transmission (a “fast

channel”). This would be suitable if you have a good line where little error

correction is necessary.
Select

Interleave

mode to use interleave delay when transmission error

correction (Reed- Solomon) is necessary due to a less than ideal telephone line.
See

Section 16.4 on page 110

for more on interleave delay.

Up Stream

The following parameters relate to upstream transmissions.

Max Rate

Type a maximum upstream transfer rate (64 to 4096 Kbps) for this profile.

Configure the maximum upstream transfer rate to be less than the maximum

downstream transfer rate.

Min Rate

Type the minimum upstream transfer rate (32 to 3000 Kbps) for this port.

Configure the minimum upstream transfer rate to be less than the maximum

upstream transfer rate.

Interleave Delay

Configure this field when you set the

Latency Mode

field to

Interleave

. Type the

number of milliseconds (1-255) of interleave delay to use for upstream transfers.

It is recommended that you configure the same latency delay for both upstream

and downstream.

Max SNR

Type the maximum upstream signal to noise margin (0-31 dB).

Min SNR

Type the minimum upstream signal to noise margin (0-31 dB). Configure the

minimum upstream signal to noise margin to be less than or equal to the

maximum upstream signal to noise margin.

Содержание IES-1248-51


































































































































































































































































































































































































Результаты поиска

Содержание IES-1248-51

Отзывы:

Бренды по названию

Популярные бренды

ZyXEL Communications IES-1248-51, Руководство пользователя

Результаты поиска

Содержание IES-1248-51

Отзывы:

Бренды по названию

Популярные бренды