ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 385

ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 117

IES-1248-51 User’s Guide

Chapter 16 xDSL Port Setup

117

16.8 Virtual Channels

Defining virtual channels (also called Permanent Virtual Circuits or PVCs) allows you to set
priorities for different services or subscribers. You can define up to eight channels on each
DSL port and use them for different services or levels of service. You set the PVID that is
assigned to untagged frames received on each channel. You also set an IEEE 802.1p priority
for each of the PVIDs. In this way you can assign different priorities to different channels (and
consequently the services that get carried on them or the subscribers that use them).

For example, you want to give high priority to voice service on one of the ADSL ports.

Use the

Edit Static VLAN

screen to configure a static VLAN on the IES-1248-51 for voice

on the port.

Use the

ADSL Edit Port Channel Setup

screen to:

• Configure a channel on the port for voice service.
• Set the channel to use the PVID of the static VLAN you configured.
• Assign the channel a high priority.

16.8.1 Super Channel

The IES-1248-51 forwards frames belonging to VLAN groups that are not assigned to specific
channels to the super channel. Enable the super channel option to allow a channel forward
frames belonging to multiple VLAN groups (that are not assigned to other channels). The
super channel functions in the same way as the channel in a single channel environment. One
port can have only one super channel.

DSCarrier(256~511)

Mask0

represents tones 256~287

Mask1

represents tones 288~319

Mask2

represents tones 320~351

Mask3

represents tones 352~383

Mask4

represents tones 384~415

Mask5

represents tones 416~447

Mask6

represents tones 448~479

Mask7

represents tones 480~511

For example, use 0x00001000 in

Mask1

to disable downstream carrier tone

307. Use 0x0000f000 in

Mask1

to disable downstream carrier tones 304 to 307.

Apply

Click

Apply

to save your changes to the IES-1248-51’s volatile memory. The

IES-1248-51 loses these changes if it is turned off or loses power, so use the

Config Save

link on the navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring the fields again.

Table 17

xDSL Port Setting (continued)

LABEL

DESCRIPTION

«
...
115
116
117
118
119
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды