ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 385

ZyXEL Communications IES-1248-51 Скачать руководство пользователя страница 109

IES-1248-51 User’s Guide

Chapter 16 xDSL Port Setup

109

C

H A P T E R

16

xDSL Port Setup

This chapter explains how to configure settings for profiles and individual ADSL ports. It also
covers how to configure virtual channels and virtual channel profiles.

16.1 ADSL Standards Overview

These are the ADSL standards and rates that the IES-1248-51 supports at the time of writing.
The actual transfer rates will vary depending on what the subscriber’s device supports, the line
conditions and the connection distance.

16.2 Downstream and Upstream

Downstream refers to traffic going out from the IES-1248-51 to the subscriber’s ADSL
modem or router. Upstream refers to traffic coming into the IES-1248-51 from the
subscriber’s ADSL modem or router.

16.3 Profiles

A profile is a table that contains a list of pre-configured ADSL settings. Each ADSL port has
one (and only one) profile assigned to it at any given time. You can configure multiple
profiles, including profiles for troubleshooting. Profiles allow you to configure ADSL ports
efficiently. You can configure all of the ADSL ports with the same profile, thus removing the
need to configure the ADSL ports one-by-one. You can also change an individual ADSL port
by assigning it a different profile.

Table 15

ADSL Standards Maximum Transfer Rates

STANDARD

MAXIMUM DOWNSTREAM

MAXIMUM UPSTREAM

G.dmt 8160

Kbps

1024

Kbps

ANSI T1.413 issue 2

8160 Kbps

1024 Kbps

ADSL2

12000 Kbps

1200 Kbps

ADSL2 Annex M

12000 Kbps

2400 Kbps

ADSL2+

25000 Kbps

1200 Kbps

ADSL2+ Annex M

25000 Kbps

2400 Kbps

«
...
107
108
109
110
111
...
»

Содержание IES-1248-51


































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды