ZyXEL Communications IES-1000 - ANNEXE 7 Скачать руководство пользователя страница 70

Страница: 70 / 139

NetAtlas IES-1000 (AAM1008) EMS User’s Guide

7-12

The Configuration Menus

Table 7-7 ADSL Line Status

LABEL DESCRIPTION

Upstream SNR
Margin

This field displays the actual upstream SNR (Signal-to-Noise Ratio) margin in decibel (dB). SNR
measures the relative strength of the ADSL signal compared to background noise.

Downstream
SNR Margin

This field displays the actual downstream SNR (Signal-to-Noise Ratio) margin in decibel (dB).

SNR measures the relative strength of the ADSL signal compared to background noise.

Port X

(where x is a port number in the

Port

column)

The following fields display information about the port.

Upstream (ATU-
R)

Downstream
(ATU-C)

ATU-R (ADSL Termination Unit-Remote) refers to the channel for traffic coming to the IES from
the subscriber (upstream).

ATU-C (ADSL Termination Unit-Central) refers to the channel for traffic going from the IES to
the subscriber (downstream).

Attenuation Attenuation measures how much the signal has degraded as it travels from the ADSL port to the

modem and vice-versa. The smaller the number, the better.

Output Power Output power indicates how much power the ADSL line is sending to the modem connected to

the port. You will see power increase as loop length increases.

Attainable Rate Attainable rate indicates the overall quality of the loop. The maximum rate for ADSL is about

1500Kbps/8000Kbps. If your attainable rate is approaching these values you have a very
good/short loop.

Interleave Delay This field displays the number of milliseconds (1-255) of interleave delay to use for

upstream/downstream transfers.

Click

Close

to close the screen

7.4 Network Configuration

The network configuration submenus consist of interface information, an IP address table, IP routing table, IP
ARP table and bridge information.

7.4.1 Interface

Information

Click

Configuration

Network Configuration

and then

Interface Info

. This information (and more) can also be

displayed by double-clicking on a port.

Содержание IES-1000 - ANNEXE 7












































































































































Результаты поиска

Содержание IES-1000 - ANNEXE 7

Отзывы:

ZyXEL Communications IES-1000 - ANNEXE 7, Руководство пользователя, Страница: 70 / 139

Результаты поиска

Содержание IES-1000 - ANNEXE 7

Отзывы: