ZyXEL Communications GS1200 SERIES Скачать руководство пользователя страница 64

Страница: 64 / 85

Chapter 14 Management

GS1200 Series User’s Guide

Figure 47

Switch Management

The following table describes the labels in this screen.

Table 16 Switch Management

LABEL

DESCRIPTION

Device Setting

Reset

Click this button to clear all Switch configuration information you configured and return to the
factory defaults.

If you want to access the Switch Web Configurator again, you may need to change the IP
address of your computer to be in the same subnet as that of the default Switch IP address
(192.168.1.3).

Reboot

Click this button to restart the Switch without physically turning the power off.

Firmware
Upgrade

Click this button to upgrade the latest firmware to the Switch.

DHCP Client

Select

Enable

if you have a DHCP server that can assign the Switch an IP address, subnet mask,

a default gateway IP address and a domain name server IP address automatically. Otherwise,
select

Disable

Содержание GS1200 SERIES






















































































Результаты поиска

Содержание GS1200 SERIES

Отзывы:

ZyXEL Communications GS1200 SERIES, Руководство пользователя, Страница: 64 / 85

Результаты поиска

Содержание GS1200 SERIES

Отзывы: