ZyXEL Communications GS1200 SERIES Скачать руководство пользователя страница 43

Страница: 43 / 85

GS1200 Series User’s Guide

Per Port Status

Port

This identifies the Ethernet port on the Switch.

Link status

This field displays the current status or speed (either 10 Mbps, 100 Mbps or 1000 Mbps) of each
port.

TX(Pkts)

This field shows the number of transmitted frames on this port.

RX(Pkts)

This field shows the number of received frames on this port.

Loop Status

It displays

Loop

when the Switch detects a loop on the port. Otherwise, it displays

Normal

PoE Status (W)

(GS1200-5HP v2
& GS1200-8HP
v2)

This field displays the amount of power the Switch is currently supplying to the PoE-enabled
device connected to the port.

Clear

Click this button to clear the statistics in the TX(Pkts) and RX(Pkts) fields.

Refresh

Click this button to update the information in this screen.

Table 6 System (continued)

LABEL

DESCRIPTION

Содержание GS1200 SERIES






















































































Результаты поиска

Содержание GS1200 SERIES

Отзывы:

ZyXEL Communications GS1200 SERIES, Руководство пользователя, Страница: 43 / 85

Результаты поиска

Содержание GS1200 SERIES

Отзывы: