ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя | Manualshive

Страница: 245 / 282

background image

Dimension ES-3148 User’s Guide

Chapter 33 IEEE 802.1Q Tagged VLAN Commands

243

C

H A P T E R

33

IEEE 802.1Q Tagged VLAN

Commands

This chapter describes the IEEE 802.1Q Tagged VLAN and associated commands.

33.1 IEEE 802.1Q Tagged VLAN Overview

See the VLAN chapter for more information on VLANs. There are two kinds of tagging:

1

Explicit Tagging

A VLAN identifier is added to the frame header that identifies the source VLAN.

2

Implicit Tagging

The MAC (Media Access Control) number, the port or other information is used to
identify the source of a VLAN frame.

The IEEE 802.1Q Tagged VLAN uses both explicit and implicit tagging.

Whether to tag an outgoing frame depends on the setting of the egress port on a per-LAN, per-
port basis (recall that a port can belong to multiple VLANs). If the tagging on the egress port is
enabled for the VID of a frame, then the frame is transmitted as a tagged frame; otherwise, it is
transmitted as an untagged frame.

33.2 VLAN Databases

A VLAN database stores and organizes VLAN registration information useful for switching
frames to and from a switch. A VLAN database consists of a static entries (Static VLAN or
SVLAN table) and dynamic entries (Dynamic VLAN or DVLAN table).

33.2.1 Static Entries (SVLAN Table)

Static entry registration information is added, modified and removed by administrators only.

«
...
243
244
245
246
247
...
»

Содержание Dimension ES-3148



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dimension ES-3148

Power Xpert Meter 2000

Бренд: Eaton Страницы: 16

POW-R-COMMAND 1000

Бренд: Eaton Страницы: 84

Бренд: Clavister Страницы: 89

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

Бренд: Abocom Страницы: 1

Бренд: ZyXEL Communications Страницы: 299

Бренд: Lanner Страницы: 63

RP614 - Web Safe Router

Бренд: NETGEAR Страницы: 16

Бренд: TP-Link Страницы: 37

Бренд: Raven Страницы: 33

Бренд: Multi-Link Страницы: 31

Бренд: MicroNova Страницы: 113

NetVanta 300 Series

Бренд: ADTRAN Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: B&B Electronics Страницы: 74

Бренд: Encore Networks Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды