ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 131 / 282

Dimension ES-3148 User’s Guide

Chapter 18 Access Control

129

Figure 57

Access Control: Logins

The following table describes the labels in this screen.

Table 38

Access Control: Logins

LABEL

DESCRIPTION

Administrator
This is the default administrator account with the “admin” user name. You cannot change the default

administrator user name. Only the administrator has read/write access.

Old Password

Type the existing system password (

1234

is the default password when

shipped).

New Password

Enter your new system password.

Retype to confirm Retype your new system password for confirmation

Edit Logins
You may configure passwords for up to four users. These people have read-only access.

User Name

Set a user name (up to 32 ASCII characters

long).

Password

Enter your new system password.

Retype to confirm Retype your new system password for confirmation

Apply

Click

Apply

to save your changes back to the switch.

Cancel

Click

Cancel

to begin configuring this screen afresh.

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды