Chapter 6 Broadband
AMG1302-T11C User’s Guide
74
6.2.1 Advanced Setup
Use this screen to edit your AMG1302-T11C's advanced WAN settings. Click the
Advanced Setup
button in the
Internet Connection
screen. The screen appears as shown.
DHCP IPv6
Select
DHCP
if you want to obtain an IPv6 address from a DHCPv6 server.
The IP address assigned by a DHCPv6 server has priority over the IP address
automatically generated by the AMG1302-T11C using the IPv6 prefix from an RA.
Select
SLAAC
(Stateless address autoconfiguration) to have the AMG1302-T11C use
the prefix to automatically generate a unique IP address that does not need to be
maintained by a DHCP server.
Select
Auto
to have the AMG1302-T11C indicate to hosts for IPv6 address generation
depending on the M/O (Managed/Other) flag values in the router advertisements
sending to hosts.
•
If M flag is 1, the AMG1302-T11C will indicate to hosts to obtain network settings
(such as WAN IP, LAN prefix and DNS settings) through DHCPv6.
•
If M flag is 0, the AMG1302-T11C will check O flag.
•
If O flag is 1, the AMG1302-T11C will indicate to hosts to obtain DNS information
and LAN prefix through DHCPv6.
•
If O flag is 0, the AMG1302-T11C will not get information through DHCPv6.
DHCP PD
Select
Enable
to use
DHCP PD
(Prefix Delegation) to allow the AMG1302-T11C to
pass the IPv6 prefix information to its LAN hosts. The hosts can then use the prefix to
generate their IPv6 addresses.
WAN Identifier
Type
Select
Manual
to manually enter a WAN Identifier as the interface ID to identify the
WAN interface. The WAN Identifier is appended to the IPv6 address prefix to create
the routable global IPv6 address. Select
EUI64
to use the EUI-64 format to generate
an interface ID from the MAC address of the WAN interface.
WAN Identifier
If you selected
Manual
, enter the WAN Identifier in this field. The WAN identifier
should be unique and 64 bits in hexadecimal form. Every 16 bit block should be
separated by a colon as in XXXX:XXXX:XXXX:XXXX where X is a hexadecimal
character. Blocks of zeros can be represented with double colons as in
XXXX:XXXX::XXXX.
Bridge and Routing mode in the same WAN
Enable Con-current
WAN
Enable this if you want to use the same VPI/VCI settings in different WAN interfaces.
Select this and then choose the ports and/or SSID to bridge with the WAN interface.
•
ADSL concurrent WAN uses the same VCI/PVI in both routing and bridge modes.
Connection (PPPoA and PPPoE encapsulation only)
Keep Alive
Select
Keep Alive
when you want your connection up all the time. The AMG1302-
T11C will try to bring up the connection automatically if it is disconnected.
Connect on Demand
Select
Connect on Demand
if you do not want the connection up all the time and
specify an idle time-out in the
Max Idle Time
field.
Max Idle Time
Specify the time in seconds that elapses before the AMG1302-T11C automatically
disconnects from the ISP.
Apply
Click this to save your changes.
Cancel
Click this to restore your previously saved settings.
Advanced Setup
Click this to display the
Advanced WAN Setup
screen and edit more details of your
WAN setup. Click this button again to display less fields in this screen.
Table 11
Network Setting > Broadband > Internet Connection (continued)
LABEL
DESCRIPTION
Содержание AMG1302-T11C
