manualshive.com logo in svg

Zte ZXV10 H100, Руководство пользователя, Страница: 13 / 44

Поделиться
Скачать
Zte ZXV10 H100 Скачать руководство пользователя страница 13

Chapter 1

Introduction of the Product

1-3

The indicators on the front panel of the ZXV10 H100 are shown below:

The meanings of the indicators on the front panel of the ZXV10 H100 are show in the

table below:

Indicators

Status

Description

On

Power-on self-test failure

Fault indicator.

Flashing

To be determined

The green indicator is

solid on

The device is powered on and the version

is being loaded/upgraded

Off

The device is powered off

Run indicator

Flashing

The device runs normally

The green indicator is

solid on

The ADSL synchronization is normal and

so is the link connection

Off

The link is not set up yet

ADSL LINK indicator

Flashing

The

link

is

being

set

up

through

hand-shake negotiation

The green indicator is

solid on

Working (switched on with the WLAN

button)

Off

Stops working (switched off with the

WLAN button)

WLAN indicator

Flashing

Flashing according to the network traffic

The green indicator is

solid on

Working (switched on with the Bluetooth

button)

Off

Stops working (switched off with the

Bluetooth button)

Bluetooth indicator

Flashing

Flashing according to the network traffic

The meanings of the indicators on the rear panel of the ZXV10 H100 are show in the

table below:

The meanings of the indicators on the rear panel of the ZXV10 H100 are show in the

Содержание ZXV10 H100













































Отзывы:

Нет отзывов