background image

 

FCC Statements 

 

 
 
Warning

:    Changes or modifications to this unit not expressly approved by the party 

responsible

 

for

 

compliance

 

could

 

void

 

the

 

user’s

 

authority

 

to

 

operate

 

the

 

equipment.

 

 
 

NOTE: 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits for  a  

Class  B  digital  device,  pursuant  to  Part  15  of  the  FCC  Rules.  These limits are  
designed  to  provide  reasonable  protection  against  harmful  interference  when  the 
equipment is  operated  in  a  commercial  environment.  This equipment generates,  
uses,  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  
accordance  with  the  instruction  manual,  may  cause  harmful  interference  to  radio 
communications. Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his own 
expense.

 

 

NOTE

: Operation  of  this  equipment  in  a  residential  area  is  likely  to  cause  harmful  

interference in which case the user will be required to correct the interference at his own 
expense. 

 

Radiation Exposure Statement

:

  

This

  

equipment

  

complies

  

with

  

FCC

  

radiation

  

exposure

  

limits

  

set

  

forth

  

for

  

an

  

uncontrolled

  

environment.

   

This

 

equipment

 

should

 

be

 

installed

 

and

 

operated

 

with

 

minimum

 

distance

 

6.5m

 

between

 

the

 

radiator

 

&

 

your

 

body.

 

 
 

Содержание ZXSDR R8882 L708


















































Отзывы: