Zte ZXR10 5900E Series Скачать руководство пользователя страница 163

Страница: 163 / 226

Chapter 13 IPv6 PIM-SM Configuration

of the multicast route entities. The Join message and the Prune message are in the

same packet. Either message can be null.

Bootstrap message: A route needs to send Bootstrap messages on all interfaces

except the interface on which the Bootstrap message is received. This message is

generated on the BSR and forwarded by all switches.

Assert message: When there are several switches on a multi-access network and a

multicast group packet is received on an egress interface of a switch, it is necessary

to use the Assert message to designate a forwarder.

Candidate-RP-Advertisement:

candidate

unicasts

Candidate-RP-Advertisement to the BSR periodically to advertise the set of group

addresses served by the Candidate RP.

13.2 Configuring IPv6 PIM-SM

To configure IPv6 PIM-SM on ZXR10 5900E, perform the following steps.

Step

Command

Function

ZXR10(config-mcast-ipv6)#

router pim

Enables IPv6 PIM-SM.

ZXR10(config-mcast-ipv6)#

no router pim

Disables PIM-SM.

ZXR10(config-mcast-ipv6-pim)#

static-rp

ip-address

riority

priority

Configures a static RP.

ZXR10(config-mcast-ipv6-pim)#

no static-rp

ip-address

priority

priority

Deletes a static RP.

ZXR10(config-mcast-ipv6-pim)#

rp-candidate

ip-address

priority

priority

Configures a candidate BSR.

ZXR10(config-mcast-ipv6-pim)#

rp-candidate

ip-address

priority

priority

Configures a candidate RP.

ZXR10(config-mcast-ipv6-pim)#

spt-threshold infinity

Configures handover of the

SPT.

ZXR10(config-mcast-ipv6-pim)#

accept-register

access-list-name

Filters the multicast packets

encapsulated in Register

messages.

ZXR10(config-mcast-ipv6-pim)#

no accept-register

Disables to filter the packets

encapsulated in Register

messages.

ZXR10(config-mcast-ipv6-pim)#

accept-rp

access-list-name

Filters the candidate RP

addresses advertised in the

Bootstrap messages.

ZXR10(config-mcast-ipv6-pim)#

no accept-rp

Disables to filter the candidate

RP addresses.

13-3

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды