Zte ZXMW NR8250 Скачать руководство пользователя страница 94

Страница: 94 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

2.5 QoS Alarm

2.5.1 134243772 EFM local link event

Alarm Property

Alarm Code: 134243772

Alarm Information: The alarm is reported if EFM detects a local link event.

Alarm Level: Major

Alarm Type: Qos Alarm

Sub-code Description

Sub-code 1: Errored Symbol Period Event

Sub-code 2: Errored Frame Event

Sub-code 3: Errored Frame Period Event

Sub-code 4: Errored Frame Seconds Summary Event

Sub-code 5: Organization Specific Event

Effect on the System

The link performance is affected.

Possible Causes

The number of errored symbols of the physical layer within the unit time exceeds the

preset threshold.

The number of errored frames of the MAC layer within the unit time exceeds the preset

threshold.

The number of errored frames of MAC layer within the unit frame amount exceeds the

preset threshold.

The number of errored frame seconds of the MAC layer within the unit time exceeds

the preset threshold.

Handling Procedure

Contact the network engineer and optimize the link performance.

2.5.2 134243778 EFM loopback alarm

Alarm Property

Alarm Code: 134243778

Alarm Information: The alarm is reported if EFM initiates loopback or responds a

loopback instruction.

Alarm Level: Minor

Alarm Type: Qos Alarm

2-80

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды