Zte ZXMW NR8250 Скачать руководство пользователя страница 86

Страница: 86 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Handling Procedure

None

2.4.6 401 DC input voltage abnormal

Alarm Property

Alarm Code: 401

Alarm Information: This alarm is reported when the DC input voltage is out of range

and cleared when the voltage becomes normal.

Alarm Level: Major

Alarm Type: Environment Alarm

Sub-code Description

Sub-code 0: Overvoltage

Sub-code 1: Undervoltage

Effect on the System

The board or the system cannot operate properly, and the services carried by the board

are interrupted.

Possible Causes

When the input voltage of PM board is higher than the upper threshold, it is

over-voltage.

When the input voltage of PM board is lower than the lower threshold, it is

under-voltage.

Handling Procedure

Over-voltage: Use a multimeter or other tools to check whether the input DC voltage is

higher than or equal to 56 V. If yes, replace the DC power supply system. If not, replace

the PM board.

Under-voltage: Use a multimeter or other tools to check whether the input DC voltage is

lower than 42 V. If yes, replace the DC power supply system. If not, replace the PM board.

2.4.7 4011 Outdoor access-control alarm

Alarm Property

Alarm Code: 4011

Alarm Information: The access-control module of the outdoor monitoring device is

abnormal.

Alarm Level: Major

Alarm Type: Environment Alarm

2-72

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды