Zte ZXMW NR8250 Скачать руководство пользователя страница 121

Страница: 121 / 124

Chapter 3 Notification

Sub-code Description

None

Effect on the System

The traffic carried by the board is not affected, but the performance data may become

incomplete.

Possible Causes

The periphral boards do not report the heartbeat message.

Handling Procedure

Ensure that the power supply to the board is normal.

3.40 134317749 Main clock reference source change

Notification Property

Notification Code: 134317749

Notification Information: The notification is reported if the main clock reference

changes. The information of the main clock reference reported contains RackNo,

SheifNo, slotNo, and portID.

Notification Type: Equipment Alarm

Sub-code Description

None

Effect on the System

none

Possible Causes

Main clock reference source change

Handling Procedure

Check link status of last Main Clock reference source if necessary.

3-25

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды