Zte ZXMW NR8250 Скачать руководство пользователя страница 105

Страница: 105 / 124

Chapter 3 Notification

3.13 134243730 Neighbor information of LLDP changed

Notification Property

Notification Code: 134243730

Notification Information: The notification is reported when the neighbor information is

changed.

Notification Type: Communications Alarm

Sub-code Description

Sub-code 1: A new neighbor is added to the port;

Sub-code 2: The ports receives the shutdown packet and the neighbor information is

deleted;

Sub-code 3: The port neighbor information is changed;

Sub-code 4: The port neighbor information addition fails;

Sub-code 5: The port neighbor information is aging and deleted.

Effect on the System

It does not affect the traffic carried by the board.

Possible Causes

The ports receives the packet of a new neighbor .

The port receives the shutdown packet from the neighbor, and deletes the information.

The port receives the neighbor information change packet.

The number of port neighbors exceeds the maximum limit 8, and no neighbor can be

added.

The port cannot receive LLDP packets from a neighbor for a long time and the neighbor

information is aging and deleted.

Handling Procedure

No processing is required.

3.14 134243731 8032 port blocked

Notification Property

Notification Code: 134243731

Notification Information: The notification is reported if the 8032 protocol sends a block

request to the switching chip and the chip is blocked.

Notification Type: Equipment Alarm

Sub-code Description

Sub-code 1: The port is blocked due to local link disconnection;

3-9

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды