Zte ZXMW NR8250 Скачать руководство пользователя страница 104

Страница: 104 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Notification Type: Communications Alarm

Sub-code Description

Sub-code 1: The LLDP global enable status is disabled;

Sub-code 2: The LLDP global enable status is enabled.

Effect on the System

This alarm does not affect the traffic carried by the board. If LLDP global enable status is

disabled, all ports cannot send the LLDP packet and will not process the received LLDP

packet.

Possible Causes

Change the configuration of LLDP global enable.

Handling Procedure

No processing is required.

3.12 134243729 Local management address of LLDP

changed

Notification Property

Notification Code: 134243729

Notification Information: The alarm is reported when the local management address

is changed.

Notification Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board.

Possible Causes

Change Local management address.

Handling Procedure

No processing is required.

3-8

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды