Zte ZXMW NR8250 Скачать руководство пользователя страница 100

Страница: 100 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Possible Causes

It is the notification of the standby-to-active changeover being completed.

Handling Procedure

None

3.5 10006 Board power-on failure

Notification Property

Notification Code: 10006

Notification Information: The notification is reported when the board fails to be

powered on due to the board's basic process power-on failure or timeout.

Notification Type: Equipment Alarm

Sub-code Description

Sub-code 1: Process power-on failure

Sub-code 2: Process power-on timeout

Effect on the System

The board fails to operate normally.

Possible Causes

The process fails to be powered on or timeout.

Handling Procedure

Check whether module timeout occurs. If yes, change the software version.

3.6 10012 Module reset

Notification Property

Notification Code: 10012

Notification Information: The module is reset.

Notification Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The module is reset.

3-4

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды