background image

ZXHN H368C

 

User’s Manual                                                         

 

16 

Customer Information 

1. 

This equipment complies with Part 68 of the FCC rules and the 

requirements adopted by the ACTA. On bottom of this equipment is a label that 

contains, among other information, a product identifier of US: 

ZTEDL01BHNH368CV1. If requested, this number must be provided to the 

telephone company. 

 

2. 

If this equipment VDSL CPE causes harm to the telephone network, the 

telephone company will notify you in advance that temporary discontinuance 

of service may be required. But if advance notice isn’t practical, the telephone 

company will notify the customer as soon as possible. Also, you will be 

advised of your right to file a complaint with the FCC if you believe it is 

necessary. 

 

3. 

The telephone company may make changes in this facilities, equipment, 

operations or procedures that could affect the operation of the equipment. If 

this happens the telephone company will provide advance notice in order for 

you to make necessary modification to maintain uninterrupted service. 

 

4. 

If you experience trouble with this equipment, you disconnect it from the 

network until the problem has been corrected or until you are sure that the 

equipment is not malfunctioning. 

 

5. 

Please follow instructions for repairing if any (e.g. battery replacement 

section); otherwise do not alternate or repair any parts of device except 

specified. 

Содержание ZXHN H368C


























Отзывы: