background image

                             ZXDSL 831A

 User’s Manual

 

iii 

WITH USING OF THIS PRODUCT, WHETHER OR NOT ZTE HAD 

BEEN ADVISED, KNEW OR SHOULD HAVE KNOWN OF THE 

POSSIBILITY OF SUCH DAMAGES, INCLUDING, BUT NOT LIMITED 

TO, LOST PROFITS, COST OF CAPITAL, COST OF SUBSTITUTE 

FACILITIES OR EQUIPMENT, ANY DOWNTIME COSTS OR CLAIMS 

OF END USERS.  THE  LIABILITY  OF  EACH  PARTY  UNDER 

THIS AGREEMENT, WHETHER ARISING OUT OF BREACH OF 

CONTRACT (INCLUDING BUT NOT LIMITED TO BREACH OF 

WARRANTY) OR TORT (INCLUDING BUT NOT LIMITED TO 

NEGLIGENCE AND STRICT LIABILITY) OR UNDER AN 

INDEMNIFICATION PROVISION SHALL IN NO EVENT EXCEED THE 

AGGREGATE AMOUNT BENIFITED BY ZTE IN THE PRODUCTS 

FROM WHICH SUCH LOSS OR DAMAGE DIRECTLY AROSE.     

 
Confidentiality 
 

End User agrees that End User will receive confidential or proprietary 

information (“Confidential Information”) in connection with the purchase 

and deployment of ZTE Equipment. End User will not disclose ZTE’s 

Confidential Information, will use it only for purposes for which it was 

disclosed, and must treat it with the same degree of care as it does its 

own similar information, but with no less than reasonable care. End 

User agrees that the terms herein, the Equipment and all ZTE 

documentation is ZTE Confidential Information. 

 

 

Содержание ZXDSL 831A II
































Отзывы: