background image

  ZTE WF821E Getting Started

 

 

Confidential and Proprietary Information of ZTE CORPORATION                                                                                      9

 

 

This  equipment  should  be  installed  and  operated  with  minimum  distance  80cm  between  the  radiator  & 

your body. 

 

To the Owner 

 

It  is  recommended  to  assemble  the  Device  on  a  fix  location,  please  consult  manufacture  before 

change location of usage. 

 

Some  electronic  devices  are  susceptible  to  electromagnetic  interference  sent  by  your  device  if 

inadequately shielded, such as the electronic system of vehicles. Please consult the manufacturer of 

your device before using if necessary. 

 

Operating your device may interfere with medical devices like hearing aids and pacemakers. Please 

always keep them more than 80 centimeters away from such medical devices when they are turned 

on. Turn your device off if necessary. Consult a physician or the manufacturer of the medical device 

before using your device. 

 

Be  aware  of  the  usage  limitation  when  using  your  device  at  places  such  as  oil  warehouses  or 

chemical factories, where there are explosive gases or explosive products being processed. Turn off 

your device if required. 

 

The use of electronic transmitting devices is forbidden in aircrafts, at petrol stations and in hospitals. 

Please observe and obey all warning signs and switch off your device in these conditions. 

 

Do  not  touch  the  inner  antenna  area  if  not  necessary.  Otherwise  it  will  affect  your  device’s 

performance. 

 

Store your device out of the reach of little children. Your device may cause injury if used as a toy. 

 

Do not touch the metallic parts of your device so as to avoid a burn, when your device is working. 

Using Your Device 

 

Please use original accessories or accessories that are authorized. Using any unauthorized accessories 

may  affect  your  device’s  performance,  and  violate  related  national  regulations  about  telecom 

terminals. 

 

Avoid  using  your  device  near  or  inside  metallic  structures  or  establishments  that  can  emit 

electromagnetic waves. Otherwise it may influence signal reception. 

 

Your device is not waterproof. Please keep it dry and store in a shady and cool place. 

 

Do not use your device immediately after a sudden temperature change. In such case, it will produce 

dew inside and outside your device, so don’t use it until it becomes dry. 

 

Handle your device carefully. Do not drop, bend or strike it. Otherwise your device will be damaged. 

 

No dismantling by non-professionals and only qualified technicians can undertake repair work. 

 

Operating temperature range of 0

 ~ +35

 and humidity range of 5% ~ 95% are recommended.

 

Limited Warranty 

 

This warranty does not apply to defects or errors in the Product caused by: 

 

  ZTE  WF821E  Getting  Started

 

Confidential and Proprietary Information of ZTE CORPORATION                                                                                      10

i.

 

Reasonable abrasion. 

ii.

 

End  User’s  failure  to  follow  ZTE’s  installation,  operation  or  maintenance  instructions  or 

procedures. 

iii.

 

End User’s mishandling, misuse, negligence, or improper installation, disassembly, storage, 

servicing or operation of the Product. 

iv.

 

Modifications or repairs not made by ZTE or a ZTE-certified individual. 

v.

 

Power failures, surges, fire, flood, accidents, actions of third parties or other events outside 

ZTE’s reasonable control. 

vi.

 

Usage of third-party products, or usage in conjunction with third-party products provided that 

such defects are due to the combined usage. 

vii.

 

Any other cause beyond the range of normal usage intended for the Product. 

End User shall have no right to reject or return the Product, or receive a refund for the Product from 

ZTE under the above-mentioned situations. 

 

This  warranty  is  End  User’s  sole  remedy  and  ZTE’s  sole  liability  for  defective  or  nonconforming 

items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited 

to  the  implied  warranties  of  merchantability  and  fitness  for  a  particular  purpose,  unless  otherwise 

required under the mandatory provisions of the law. 

Limitation of Liability 

 

ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages 

resulting from or arising out of or in connection with using of this product, whether or not ZTE had 

been  advised,  knew  or  should  have  known  of  the  possibility  of  such  damages,  including,  but  not 

limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, 

or any downtime cost. 

FAQ and Troubleshooting 

Problem 

Suggested Solution 

My  PC  cannot  connect  to 

the CPE.

   

 

Re-plug the PC Ethernet cable and check if the PC LAN connection 

is up or showing activity.   

 

Check if the 12V DC power adapter is working. If it is not, check 

the power cord and make sure it is connected properly. Also verify 

that the AC power supply is available.   

 

If  the  PC  LAN  shows  no  activity  and  CPE  Power  LED  is  off  but 

the power cord and ETH cable are connected properly and there is 

AC supply,  then it is  likely  the  Power  adapter  is damaged.  Please 

contact distributor to obtain replacement part. 

 

My  PC  cannot  acquire  IP 

from the CPE. 

 

First check if the NIC is up and working properly. Then check the 

PC NIC configuration and make sure the DHCP is enabled. 

Содержание WF821E







Отзывы: